ABB Inora 1 Gang 1 Way 10AX Switch White BL101

The ABB Inora BL101 combines simple one-point circuit control with a clean white finish suited to contemporary UAE homes, offices and fit-out projects. Its single-gang design provides straightforward operation, while the 86 x 86 mm format supports coordinated planning for common wall-switch layouts, subject to back-box compatibility.

Isolate the supply before inspection or maintenance. Clean the faceplate with a soft, slightly damp cloth and avoid solvents, abrasive cleaners or excessive water. If the switch becomes hot, discoloured, loose, cracked or intermittent, stop using the circuit and arrange inspection and replacement by a qualified electrician.

The electrician should check terminal tightness, conductor identification, earthing continuity where applicable, insulation resistance, polarity, circuit protection and secure mounting. The connected load should be confirmed as compatible with the 10A rating, and the rocker should operate smoothly without arcing, overheating or abnormal noise.

The BL101 is a 10A control switch and should not automatically be selected as the primary switch for a higher-rated socket outlet circuit. UAE socket circuits commonly require devices matched to their specific circuit and load ratings. Use a dedicated switched socket, double-pole switch or isolator where required by the load, project design and local regulations.

Only install it where the environmental conditions and applicable electrical-zone rules permit. For bathrooms, kitchens, balconies or outdoor locations, consider moisture, condensation, dust and water exposure. The supplied data does not state an IP rating, so it should not be treated as weatherproof; exposed or damp locations require a suitably IP-rated enclosure or an alternative weather-resistant switch.

Yes. Its standard single-gang format and neutral white appearance make it suitable for villas, apartments, offices, retail spaces and other fit-out projects. Contractors should coordinate the switch position, mounting box, conduit route, cable size and final finish during first-fix and second-fix electrical works.

The switch has approximate face dimensions of 86 x 86 mm. Select a compatible flush or surface-mounted box with suitable fixing points and enough internal depth for the 41.5 mm product profile, terminals and conductor bend radius. Confirm box compatibility and required installation depth before blockwork, plastering or drywall closure.

First isolate the circuit at the distribution board and verify that it is de-energised with an appropriate tester. A qualified electrician should identify the incoming live conductor and switched-live conductor, connect them to the terminals indicated on the product, secure the switch to a compatible wall box, fit the faceplate and test operation. The neutral conductor is normally not switched in a basic one-way lighting circuit, but wiring must follow the terminal markings and approved project drawings.

It may control a compatible fan or light-duty electrical load if the equipment's running current, starting current and switching characteristics are within the approved rating. Motors, pumps, air-conditioning equipment, water heaters and other high-load appliances may require a correctly rated isolator, contactor or dedicated control device rather than direct switching through the BL101.

Yes. The BL101 is primarily suited to switching a single lighting circuit from one point, including compatible LED, fluorescent or conventional lighting loads. The total operating current and any LED driver inrush current must remain within the switch and circuit design limits specified for the installation.

Yes, it can be used in suitable UAE residential and commercial installations when the circuit voltage, connected load, wiring method and back box are compatible. Installation should follow the current requirements of the relevant UAE authority, project specifications and applicable low-voltage wiring practices. Final selection and connection should be confirmed by a licensed electrician.

The key specifications are a 10A current rating, one-gang configuration, one-way switching operation, white finish and approximate dimensions of 86 x 86 x 41.5 mm. The product SKU is 42211-NOS, the model is Inora BL101 and the listed EAN is 6941593436071.

It's a single-gang, single-throw light switch rated for up to 10 amps, finished in white, and part of ABB's Inora design line.

The ABB Inora BL101 is a white, single-gang, one-way wall switch designed to control one electrical circuit from one location. Its 10A rating makes it suitable for compatible lighting and other approved control applications, while the clean 86 x 86 mm faceplate complements residential, commercial and construction interiors.