ABB Inora 1 Gang 1 Way 20AX Double Pole Switch with Illumination, Small Rocker White BL111S

Verify SKU 42205-NOS, model INORA BL111S, one-gang and one-way operation, 20A rating, double-pole switching, neon indicator, white finish and approximate dimensions of 28.7 × 86 × 86 mm. The listed EAN is 6941593436385. Confirm circuit compatibility and project approval before ordering for installation.

Keep the faceplate clean and dry, using a soft cloth without abrasive or solvent-based cleaners. During scheduled electrical maintenance, isolate the supply and have a qualified electrician check for discoloration, heat damage, loose mounting, unusual buzzing, unreliable operation or a failed neon indicator. Any damaged or overheating switch should be replaced after the underlying circuit condition has been investigated.

Contractors should review the electrical load schedule, circuit voltage, current and load category, cable and protective-device coordination, required method of isolation, back-box dimensions, environmental conditions and approved material submittal. They should also verify any required conformity documents, test certificates and consultant or authority approvals for the specific project.

Yes, it is suitable for consideration in villas, apartments, offices, retail units and other commercial fit-outs where a white one-gang 20A double-pole switch is specified. Contractors should confirm the approved brand schedule, load requirements, back-box compatibility, faceplate appearance and local authority requirements before bulk installation.

It may be considered for appropriate indoor kitchen or bathroom applications only when its location, enclosure and installation comply with the required electrical zones and environmental protection rules. No IP rating is provided in the listed product data, so it should not be assumed to be weatherproof or splash-resistant. Outdoor, wet or dusty construction areas require a suitably IP-rated enclosure or a purpose-designed weatherproof switch.

No. The BL111S is a control and isolation switch; it is not a substitute for overcurrent or earth-leakage protection. The circuit must retain correctly rated protective devices, such as an MCB or RCBO and any required RCD protection, in accordance with the distribution-board design and applicable UAE electrical regulations.

Not automatically. The appliance's normal current, startup or inrush current, load type, duty cycle and manufacturer-specified isolation method must all be considered. Cable size, circuit breaker rating and protective devices must also coordinate with the load and switch. A qualified electrical engineer or electrician should verify the complete circuit rather than selecting the switch solely by its 20A rating.

The listed product dimensions are approximately 28.7 × 86 × 86 mm. The installer should use a compatible one-gang back box with sufficient depth for the mechanism, cable bending radius and secure terminations. Before procurement for a construction project, confirm the mounting centres, box depth and compatibility with the selected conduit, trunking or concealed wiring system.

No. A 20A double-pole switch forms part of the fixed electrical installation and should be fitted by a qualified or licensed electrician. Incorrect isolation, conductor selection, terminal tightening or neon wiring can create electric-shock, overheating and fire risks. Professional installation also helps ensure compliance with UAE authority and project requirements.

Installation generally involves isolating and proving the circuit dead, checking the back box and cable capacity, identifying the incoming and outgoing conductors, and terminating them at the designated double-pole terminals according to the manufacturer's diagram. The neon indicator connections must also follow the supplied instructions. After fixing and alignment, the electrician should perform continuity, insulation resistance, polarity and functional tests before energising the circuit.

UAE low-voltage installations commonly operate at approximately 230V and 50Hz for single-phase circuits. Before installation, verify that the voltage, frequency and load category marked on the product or stated in ABB documentation match the circuit. A 20A current rating alone does not confirm compatibility with every appliance or load type.

The 20A double-pole format is widely used in UAE residential and commercial projects for local appliance isolation. Suitability must still be confirmed against the project's approved specifications, the marked voltage and current ratings, and the requirements of the relevant local authority, such as DEWA, ADDC or the applicable emirate utility. Installation should be completed by a licensed electrician in accordance with current UAE regulations.

Subject to circuit design and appliance requirements, this switch may be used to control suitable fixed electrical loads such as water heaters, exhaust fans, kitchen equipment, air-conditioning accessories and other appliances requiring double-pole isolation. The connected load must not exceed the switch rating, and motor, heating or inductive loads must be assessed for starting current and switching characteristics.

This is a white 1-gang, 1-way switch rated for up to 20 amps, featuring a double-pole mechanism and a built-in neon indicator to help you locate it in the dark. It’s designed to control a high‑current circuit while providing easy visibility in low light.