ABB Inora 2 Gang 1 Way 10AX Switch White BL102

Keep the switch clean and dry, and wipe the surface only with a soft cloth after isolating the circuit when necessary. Do not use abrasive cleaners or allow water to enter the mechanism. Replace the switch if there is cracking, discoloration, looseness, arcing noise, overheating, or unreliable operation. Any inspection, terminal tightening, testing, or replacement should be performed by a qualified electrician.

Contractors should confirm the required quantity of gangs, 1 way switching arrangement, 10A load suitability, wall-box compatibility, dimensions, finish, cable capacity, and project-approved brand or wiring accessory schedule. They should also verify compatibility with the selected faceplate system and obtain any required technical submittals, approvals, or compliance documents before bulk installation.

No. As a 1 way switch, the BL102 is intended to control each connected circuit from one location. Staircases, corridors, large rooms, and entrances where one light must be operated from two locations normally require compatible 2 way switches and the appropriate interconnecting wiring.

The product data does not state an IP rating, so it should be treated as an indoor switch for dry locations unless ABB documentation confirms otherwise. In bathrooms, kitchens, balconies, gardens, and other damp or dusty locations, positioning and enclosure protection must meet the required electrical zones and local regulations. Outdoor use generally requires a suitably rated weatherproof enclosure or a dedicated IP-rated switch.

It should not be selected for heavy appliances solely because their normal operating current appears to be below 10A. Air conditioners, pumps, water heaters, and motors may require double-pole isolation, higher current ratings, motor-rated switching, contactors, or dedicated control devices. A qualified electrician or electrical engineer should select the switching and protective equipment based on the appliance load and UAE project requirements.

The 10A rating and white modular appearance make the ABB BL102 relevant to common residential and commercial lighting applications in the UAE. Product selection and installation must still comply with the approved project specification, local authority requirements, and applicable UAE electrical regulations. Where referenced by the relevant authority or consultant, wiring practices may also need to align with BS 7671 or other adopted standards.

A compatible concealed or surface-mounted wall box with adequate depth is required. The listed product dimensions are 35.2 x 86 x 41.5 mm, but installers should verify the fixing centres, terminal clearance, cable bend radius, and box depth before purchase or installation. Extra depth may be needed where larger conductors, multiple cables, connectors, or conduit entries are present.

A standard mechanical 1 way switch normally interrupts the live conductor and may not require a neutral connection at the switch itself. However, the actual wiring arrangement must be confirmed from the terminal markings, ABB documentation, and the project drawings. Neutral conductors must never be connected to switching terminals unless the manufacturer specifically requires it.

Installation should be completed by a qualified electrician. The circuit must first be isolated, locked out where applicable, and tested to confirm it is de-energised. The incoming live conductor and the two switched-live conductors should then be connected to the terminals indicated on the product, following ABB instructions and the circuit design. After securing the switch in a compatible wall box, the electrician should check terminal tightness, earthing continuity where applicable, insulation resistance, polarity, operation, and faceplate alignment before energising the circuit.

It may be used with compatible LED lighting circuits, provided the steady-state current and driver inrush current are suitable for the switch. LED drivers can produce a high momentary current when switched on, even when their normal wattage is low. For projects with multiple LED fittings or high-inrush drivers, the electrician should confirm switching capacity and use a contactor or other suitable control device if required.

This switch is suitable for indoor lighting control in villas, apartments, offices, shops, hotels, warehouses, and other UAE buildings. Typical uses include controlling two lighting zones, a light and a compatible fan circuit, or two separate room fixtures from one wall position. The connected equipment must be suitable for mechanical switch control and must not exceed the permitted electrical load.

The ABB Inora BL102 has a stated current rating of 10 amps. The connected load must remain within the switch rating and the applicable circuit design limits. Electricians should also consider the load type, operating voltage, LED driver inrush current, conductor size, protective device, and any manufacturer derating requirements before installation.

It's a dual-gang wall switch plate with two independent on/off switches. Each switch controls a separate lighting circuit, letting you operate two lights from a single wall plate. It’s finished in white for a clean, modern look and is rated for up to 10A.

The ABB Inora BL102 is a white, 2 gang, 1 way wall switch designed to control two independent electrical circuits from one location. Each rocker operates a separate circuit, making it suitable for applications such as controlling two lighting groups in a room. It has a stated 10A rating, compact dimensions of 35.2 x 86 x 41.5 mm, and a modern finish suitable for residential, commercial, and construction projects in the UAE.