ABB Inora 1 Gang 1 Way 10AX Switch Classic Grey BL101-G

One gang means the switch has one control rocker. One way means it switches a lighting circuit from a single location. The 10AX designation indicates a 10 A switch tested for lighting loads, including loads that can produce higher inrush current than a purely resistive load. The connected load must remain within the manufacturer's specified rating and the circuit design requirements.

It is intended for standard building lighting applications and may be used in UAE projects when its rating, mounting arrangement and product approvals satisfy the project specification and the requirements of the relevant local authority. UAE installations commonly operate at 230 V and 50 Hz, but compatibility and compliance should always be confirmed by the project's electrical engineer or licensed electrician before installation.

This switch is suitable for controlling a single lighting point or lighting circuit in villas, apartments, offices, shops, hotels, schools and other indoor buildings. Typical uses include bedrooms, living rooms, corridors, kitchens and enclosed utility areas. It should not be used outdoors, in wet areas or in exposed dusty locations unless installed within a suitably rated enclosure and approved for that environment.

No. The BL101-G is a one-way switch and is intended to control a circuit from one location only. For staircases, long corridors, rooms with two entrances or any application requiring control from two locations, use compatible two-way switches and the appropriate wiring arrangement.

The 10AX rating is intended to accommodate common lighting loads, including loads with switching inrush. However, LED drivers can have substantial startup current even when their normal wattage is low. The electrician should check the LED driver specifications, total connected load, inrush current and the switch manufacturer's technical data before connecting multiple LED fittings.

Installation should be completed by a qualified electrician. The circuit must be isolated and proven dead before work begins. The incoming live conductor and switched-live conductor are connected to the terminals identified in the ABB wiring instructions, after which the mechanism is secured to a compatible flush or surface box and aligned with the matching plate. Terminal markings, conductor preparation and tightening requirements in the official product instructions must be followed.

A conventional one-way mechanical light switch normally interrupts the live conductor and generally does not require a neutral connection at the switch mechanism. Actual site wiring can differ, so the electrician must identify conductors correctly and follow the terminal diagram supplied with the product. A neutral must never be assumed based only on cable colour.

The switch should be fitted to a compatible one-gang electrical back box and used with the appropriate ABB Inora mounting and cover components specified for the BL101-G. Before ordering for a construction project, confirm the box dimensions, fixing centres, installation depth and whether the selected listing includes all required faceplate or frame components.

This model is primarily intended for lighting control. It should not be selected for socket outlets, water heaters, air-conditioning equipment, pumps or other heavy or motor-driven loads solely on the basis of its 10AX marking. Such equipment may require a higher-rated double-pole switch, isolator, contactor or dedicated control device selected according to the load and UAE project requirements.

The standard indoor switch should not be assumed to have weatherproof or splash-proof protection. Bathrooms, balconies, gardens and external areas may require specific IP-rated accessories, suitable enclosures and installation outside prescribed wet-area zones. UAE heat, humidity, condensation, dust and water exposure should be considered when selecting accessories for these locations.

Contractors should verify the 10AX load suitability, one-way switching requirement, compatible back box and plate system, finish, environmental conditions and required product certifications. Installation should conform to the approved project drawings, local authority requirements and applicable electrical regulations, including relevant DEWA, ADDC or other emirate-specific requirements where applicable.

Classic grey provides a neutral, contemporary appearance that coordinates well with concrete-effect finishes, metal fixtures, grey joinery and modern commercial interiors. For multi-unit construction projects, confirm the colour reference and use the same ABB Inora range across each area to maintain a consistent appearance.

Isolate the electrical supply before inspection or maintenance. Clean the visible surface with a soft, dry or slightly damp cloth and avoid abrasive pads, solvents, strong chemicals and direct water spray. If the rocker feels loose, produces unusual heat, crackles, shows discoloration or operates intermittently, stop using it and arrange inspection by a qualified electrician.

Yes, it can be considered for new villas, apartment developments, office fit-outs, retail projects and renovation work requiring a single-location lighting switch. During refurbishment, the installer should first check the existing back box, cable condition, conductor identification, circuit protection and compatibility with the ABB Inora accessory system.