ABB Inora 1 Gang 1 Way 20AX Double Pole Water Heater Switch with LED, Marked ON Royal Gold BL180WH-PG

One gang means the accessory has one switch control. One way means the connected circuit is operated from a single switching point. DP stands for double pole, indicating that both live and neutral conductors are disconnected when the switch is turned off. This provides more complete isolation than a single-pole switch, subject to correct installation.

The 20AX marking identifies the switch rating and indicates enhanced suitability for certain lighting loads that can produce higher switching currents, including some fluorescent or inductive circuits. The connected load, supply voltage, inrush current and manufacturer data must still be checked before selection. A qualified electrician should confirm that the switch is appropriate for the intended equipment.

The LED provides a visible status indication, while the clearly marked ON position helps users identify the switch state quickly. This can be useful for fixed appliances, utility equipment and circuits where the operating status may not otherwise be obvious. The exact LED behaviour depends on the product's terminal arrangement and wiring method, so installation should follow the ABB wiring diagram supplied with the unit.

It may be used as a local control or isolation switch for compatible fixed electrical loads in homes, offices, shops, hotels and other buildings. Typical applications can include selected lighting circuits, ventilation equipment and fixed appliances within the switch rating. It must not be used for loads exceeding its electrical or inrush-current capacity, and it is not a substitute for a circuit breaker, RCD or dedicated isolator where one is required.

Yes, it is relevant to UAE residential and commercial projects that use compatible low-voltage electrical systems and require a 20AX double-pole wall switch. Final selection and installation should comply with the applicable regulations of the local authority, such as DEWA requirements in Dubai or the relevant emirate's electricity authority, as well as project specifications and applicable IEC-based wiring practices.

Installation should be completed by a licensed electrician. The circuit must first be isolated, locked out where required and tested to confirm it is de-energised. The supply and load conductors should then be connected to the identified double-pole terminals according to the ABB diagram, with earthing maintained at the box or designated terminal as applicable. After secure mounting, the electrician should test polarity, insulation, continuity, LED operation and functional switching before energising the circuit.

Check the supply characteristics, connected-load current, load type, starting or inrush current, conductor size, terminal markings and back-box compatibility. Also confirm that the circuit has correctly rated overcurrent and residual-current protection where required. Cable terminations must be secure and tightened to the manufacturer's specified torque, and the switch rating must never be treated as permission to oversize the protective device.

No. This is a 1 way switch intended to control a circuit from one location. A circuit requiring operation from two positions, such as a staircase or corridor light, normally needs a suitable 2 way switching arrangement. The selected accessories and wiring design should be verified by the project's electrical engineer or electrician.

Suitability cannot be determined from the appliance name alone. Air conditioners, water heaters and other fixed equipment may have high continuous current, motor-starting current or dedicated isolation requirements. The appliance nameplate, manufacturer instructions, circuit design and local regulations must be reviewed. Use a correctly rated dedicated isolator or contactor arrangement if the equipment exceeds the switch's permitted load characteristics.

It should only be installed in locations permitted by its declared ingress-protection rating and ABB installation instructions. Do not assume that the decorative Royal Gold finish makes it weatherproof. Outdoor areas, bathrooms, kitchens and other damp or dusty locations may require an appropriately rated enclosure, safe-zone placement and additional electrical protection under applicable UAE regulations.

Use a compatible back box of adequate depth and the correct mounting arrangement for the ABB Inora range. The box must provide enough space for the double-pole conductors without sharp bends or compressed terminations. Confirm accessory dimensions, screw centres, cable size and box compatibility before procurement, particularly for large construction projects where back boxes may already be installed.

No. The ABB Inora DP switch provides manual switching and isolation of live and neutral conductors, but it does not replace an MCB, RCBO or RCD. The circuit still requires properly designed protection against overload, short circuit and earth leakage in accordance with the distribution-board schedule, load assessment and applicable UAE electrical requirements.

Isolate the circuit before inspection or maintenance. Clean the front surface with a soft, dry or slightly damp cloth and avoid abrasive pads, solvents and strong chemical cleaners that could damage the Royal Gold finish or LED window. If the switch becomes hot, discoloured, loose, noisy or intermittent, stop using the circuit and have a qualified electrician inspect the load and terminations.

The ABB Inora BL180WH-PG combines 20AX switching, double-pole isolation, visible LED status indication and an ON marking in a decorative Royal Gold finish. It is a practical choice for contractors, consultants and property owners seeking a coordinated ABB wiring accessory for compatible indoor circuits. Compliance should always be confirmed against the approved project submittal, load schedule and local authority requirements.