ABB Inora 1 Gang 1 Way 20AX Double Pole Switch with LED Royal Gold BL111-PG

One gang means the faceplate contains one switch mechanism. One way means the load is controlled from a single switching position rather than from two locations. DP stands for double pole, indicating that the switch can disconnect both live and neutral conductors simultaneously when correctly installed.

The 20AX marking identifies the switch rating for compatible AC loads, including lighting circuits with higher switching inrush than simple resistive loads. It should not be interpreted as automatic approval for every 20 A appliance, motor, water heater or inductive load. Contractors must verify the load type, operating current, inrush current, cable size, protective device and ABB technical documentation before installation.

The integrated LED offers convenient visual identification in low-light conditions or can indicate circuit status, depending on the product's supported terminal arrangement and wiring method. The electrician should follow the connection diagram supplied with the switch because LED behaviour may vary according to whether it is wired as a locator or status indicator.

It is suitable for compatible indoor residential, commercial and hospitality applications, including villas, apartments, offices, shops and fit-out projects. Typical uses may include lighting or suitable fixed-load circuits that benefit from double-pole switching. Final suitability must be confirmed against the connected equipment's electrical rating and installation instructions.

Suitability cannot be determined from the 20AX marking alone. Water heaters, air-conditioning equipment, pumps and motors may require a dedicated isolator, higher utilization category, contactor, fused connection unit or local isolation device. A qualified electrical engineer or electrician should assess the equipment current, starting load, manufacturer requirements and applicable UAE authority regulations before selecting this switch.

Installation should be completed by a licensed electrician with the circuit isolated, locked out where applicable and verified dead. The correct mounting box and cable conductors should be prepared, live and neutral connected to the designated input and output terminals, and protective earth maintained in accordance with the wiring design. Terminals must be tightened to ABB's specified torque, conductors must not be exposed, and the faceplate should be aligned without overtightening. The circuit and LED function must then be tested before handover.

Not always. A double-pole switch generally needs both live and neutral conductors at the switch position, while many conventional lighting switch points contain only a live feed and switched live. The existing back box depth, cable arrangement, circuit rating and terminal identification must be inspected by a qualified electrician before replacement.

No. A 1-way switch is intended to control a circuit from one location. Staircases, corridors and rooms requiring control from two positions normally need compatible 2-way switches and the appropriate interconnecting wiring. Multi-location control may require an intermediate switch or a dedicated control system.

The electrician should perform the tests required by the approved project procedure and local regulations. These may include protective conductor continuity, insulation resistance, polarity, earth-fault loop or protective-device verification, functional operation, double-pole disconnection and LED operation. Test results should be documented where the installation forms part of a construction or fit-out project.

Yes. Its decorative royal gold finish suits premium villas, apartments, hotels, offices and retail interiors commonly specified in UAE developments. For project use, consultants and contractors should confirm the switch rating, approved product schedule, mounting compatibility, environmental conditions and compliance requirements of the relevant authority, such as DEWA, ADDC or the applicable local electricity provider.

The complete installation should comply with applicable UAE electrical regulations, local authority requirements, approved project specifications and the manufacturer's instructions. Depending on the project and product certification, standards such as BS EN 60669-1 for household and similar fixed electrical switches may be relevant. Contractors should verify current certificates, authority approvals and consultant acceptance before procurement for regulated projects.

It should not be assumed to be weatherproof from the product name alone. For outdoor areas, bathrooms, utility spaces or dusty construction environments, verify the product's stated IP rating and applicable zone requirements. Where additional protection is required, use a suitable weatherproof enclosure or an appropriately IP-rated switch approved for the location.

Confirm model BL111-PG, royal gold finish, 1-gang and 1-way configuration, 20AX rating, double-pole operation, LED wiring requirement, mounting-box compatibility and required quantity. For construction projects, compare these details with the approved material submittal, load schedule, room data sheet and consultant specification to avoid mismatched mechanisms or finishes.

Keep the switch in its packaging until final-fix installation and protect it from cement dust, paint, plaster, moisture and abrasive cleaning products. Do not use sharp tools or harsh chemicals on the decorative surface. Install the faceplate after heavy construction work is complete, then clean it with a soft, dry or lightly damp cloth.