ABB Inora 1 Gang 1 Way 20AX Double Pole Switch with Illumination, Small Rocker Royal Gold BL111S-PG

One gang means the accessory has one independently operated rocker. One way means the connected circuit is controlled from a single switch position rather than two separate locations. DP stands for double pole, indicating that the switch opens or closes both the live and neutral conductors simultaneously. This configuration is commonly used for fixed appliances and circuits where enhanced local isolation is required.

The 20AX marking identifies the switch's current and load-switching classification. An AX-rated switch is designed to handle compatible loads with higher inrush currents than a basic resistive-load switch, subject to ABB's published specifications. The connected load, cable size, protective device and installation method must all be checked by a qualified electrician; the 20AX marking should not be treated as permission to exceed the circuit design rating.

The integrated LED provides a visible status indication, making the switch easier to identify or monitor in locations such as kitchens, utility rooms, service areas and plant spaces. The exact LED function may depend on the product's internal configuration and terminal arrangement, so the installer should follow the wiring diagram supplied with model BL111S-PG rather than assuming whether the LED indicates power availability or the switched-on state.

This switch may be used as a local control or isolation point for compatible fixed loads in residential, commercial and light-duty construction projects. Typical applications can include selected water heaters, ventilation equipment, utility appliances and other fixed electrical equipment, provided the equipment load and inrush current fall within the manufacturer's rating. It is not a substitute for a circuit breaker, residual-current protection or a dedicated isolator where regulations or equipment instructions require one.

It can be considered for compatible UAE projects designed around the commonly used 230 V, 50 Hz supply, but suitability must be confirmed against the ABB product documentation, project specifications and the requirements of the relevant local authority. Depending on the emirate and project, this may include DEWA, ADDC, SEWA or another authority having jurisdiction. Installation should also follow applicable UAE electrical regulations and relevant IEC-based requirements.

Installation must be completed by a qualified electrician. The circuit should first be isolated at the distribution board, locked or clearly secured against reconnection and verified dead with an approved tester. Conductors must then be identified and connected only to the terminals shown in ABB's wiring diagram, with both poles correctly arranged and terminal screws tightened to the specified torque. After fitting the switch securely into a compatible mounting box, the electrician should perform continuity, insulation, polarity and functional tests before energising the circuit.

Not necessarily. A double-pole switch requires the appropriate incoming and outgoing conductors at the switch position, including the neutral conductors intended to be switched. Many standard lighting switch points contain only live conductors and therefore may not support a direct replacement. An electrician should inspect the wiring, mounting box depth, conductor size, circuit rating and load type before selecting this model as a retrofit.

Contractors should verify the scheduled load, supply voltage, inrush characteristics, cable size, protective-device rating, required isolation method and compatibility with the selected mounting box and ABB Inora accessories. They should also confirm the Royal Gold finish against approved interior samples, review the LED indication requirement and check whether the location needs a higher ingress-protection rating. Product approvals and authority compliance documents should be included in the material submittal where required by the consultant.

It should not be assumed suitable for exposed outdoor, wet or dusty locations unless the complete installed assembly has an ingress-protection rating appropriate to the environment. For bathrooms, balconies, external service areas or wash-down zones, use a suitable weatherproof enclosure or an accessory specifically rated for those conditions. Required clearances from water sources and local UAE electrical rules must also be observed.

No. The ABB Inora BL111S-PG is a switching and local-isolation accessory, not an overcurrent or earth-leakage protective device. The circuit still requires correctly selected protection at the distribution board, such as an MCB or RCBO, along with RCD protection where required by the applicable regulations and circuit type.

Isolate the electrical supply before cleaning and use a soft, dry or slightly damp cloth. Do not apply abrasive pads, solvents, acidic cleaners or excessive water, as these may damage the Royal Gold surface, LED window or plastic components. During construction, protect the switch from paint, cement dust and impact, and do not operate it if the faceplate, rocker or terminals appear damaged.