ABB Inora 1 Gang 2 Way 10AX Switch Royal Gold BL105-PG

One gang means the switch has one control rocker for a single circuit. Two way means it provides common, L1 and L2 switching connections for controlling a light from either of two positions. The 10AX designation indicates a 10 A switch rating with additional suitability for the switching characteristics of certain lighting loads, including loads that can produce higher starting currents. The connected load must still remain within the manufacturer's stated limits.

This switch is commonly installed at both ends of a corridor, at the top and bottom of a staircase, at two entrances to a room, or beside the entrance and bed in a bedroom. It can also be used as a conventional one-location light switch if wired appropriately, although its main benefit is two-location control.

It is suited to indoor residential and commercial projects where the electrical design, mounting arrangement and circuit ratings are compatible. For UAE installations, the complete wiring system should comply with applicable local authority requirements, such as those of DEWA, ADDC or the relevant emirate authority, together with the project's approved specifications. Product certification, voltage compatibility and authority approval should be confirmed from current ABB documentation before installation.

It can generally be used for switching compatible LED lighting circuits, provided the total connected load and the LED drivers' inrush current remain within ABB's specified limits. LED drivers can draw a brief startup current significantly higher than their normal operating current, so an electrician should assess driver quantity and type rather than relying only on total wattage.

A typical two-way circuit uses two compatible switches. The permanent live is connected to the common terminal of the first switch, two strapper conductors connect the corresponding L1 and L2 terminals between the switches, and the common terminal of the second switch feeds the light. The neutral normally runs directly to the luminaire and is not switched. Terminal markings and the official ABB wiring diagram must take priority because layouts can vary.

Installation should be completed by a qualified electrician familiar with UAE electrical regulations and the project's approved wiring design. The circuit must be isolated at the distribution board, locked out where appropriate and proven dead with a suitable tester before work begins. Correct conductor identification, terminal tightening, earthing continuity and functional testing are essential.

Confirm that the model is BL105-PG, the circuit and lighting load are compatible with the 10AX rating, and the switch fits the selected wall box, support frame and cover arrangement. The installer should also check conductor size, terminal markings, cable condition, earth continuity and the required mounting depth. Compatibility with other ABB Inora accessories should be verified using current manufacturer information.

Do not assume that a standard decorative indoor switch is weatherproof. Installation in bathrooms, balconies, gardens, service yards or other wet and dusty environments requires the correct IP-rated enclosure, compliant location and suitable electrical protection. The electrician must observe the applicable bathroom zones and UAE authority requirements. For exposed outdoor use, select a purpose-designed weatherproof switch.

Yes. The Royal Gold colour can complement premium villas, apartments, hotels, reception areas and decorative commercial fit-outs. For a consistent result, designers and contractors should coordinate the switch with matching ABB Inora sockets, frames and accessories, subject to range compatibility. A physical sample is recommended because perceived colour can vary under different lighting conditions.

This product is an on/off two-way switch and does not itself provide dimming. A compatible dimming arrangement requires a suitable dimmer, dimmable lamps and compatible LED drivers. Not every dimmer supports conventional two-way wiring, so the control method should be checked against the dimmer manufacturer's diagram and ABB product guidance.

The completed circuit should undergo the tests required by the approved project procedure and applicable wiring regulations. These may include protective conductor continuity, insulation resistance, polarity, earth-fault loop or protective-device verification, and functional operation from both switch positions. Test results should be recorded where required for inspection, handover or authority approval.

Isolate the circuit before maintenance. Clean the visible surface with a soft, dry or slightly damp cloth, and avoid abrasive pads, solvent-based cleaners and harsh chemicals that may damage the Royal Gold finish. If the rocker becomes loose, produces unusual heat or noise, shows discoloration, or operates intermittently, stop using it and arrange inspection by a qualified electrician.

This ABB light switch combines practical two-location lighting control, a 10AX switching classification and a decorative Royal Gold appearance. It is a relevant choice for UAE villa, apartment, hospitality and commercial fit-out projects requiring a single-circuit two-way wall switch, provided compatibility and local installation requirements are confirmed.