ABB Inora 2 Gang 13A Single Pole Switched Socket Outlet Classic Grey BL227-G

This ABB Inora accessory has two 13A socket outlets, individual single-pole switches, model number BL227-G and a classic grey faceplate. It is intended for use on compatible UAE low-voltage final circuits. Installers should verify the product markings, terminal arrangement, back-box requirements and applicable circuit load before installation.

Yes, a 13A switched socket is commonly used in UAE homes, offices, hotels, shops and other buildings that employ British-style plug systems. Installation must comply with the current UAE electrical requirements, the regulations of the relevant local authority such as DEWA or the applicable emirate utility, and the project consultant's approved specifications.

The 13A rating and British-style configuration are intended for compatible 13A plug applications typically associated with BS 1363 systems. Before procurement or installation, confirm the compliance markings shown on the supplied product and ensure that the plug, socket, wiring system and protective devices meet the project's specified standards.

It is suitable for indoor applications including living rooms, bedrooms, offices, meeting rooms, retail spaces, hotel rooms and similar dry locations. The two outlets can serve equipment such as televisions, computers, chargers and small appliances, provided the connected load remains within the socket and circuit ratings.

Yes, both outlets can be used simultaneously, and each has its own switch. However, the total demand must remain within the capacity of the final circuit, protective device, cable and local electrical design. High-load appliances should not be combined without checking the calculated circuit load and diversity requirements.

Installation should be completed by a qualified electrician. The supply must first be isolated and proven dead. The live, neutral and earth conductors are then terminated at the clearly marked terminals according to the manufacturer's instructions, with correct polarity, conductor preparation and terminal tightening. The socket is secured to a compatible wall box, aligned and tested before the circuit is energized.

Use a compatible double-gang wall box with sufficient depth for the socket mechanism, conductors and safe cable bending. The required depth can vary with the wiring method, conductor size and number of cables entering the box. Confirm the ABB product drawing and project specification before cutting blockwork, gypsum board or decorative wall finishes.

The electrician should carry out the tests required by the applicable UAE regulations and project inspection plan. These commonly include protective-conductor continuity, insulation resistance, polarity, earth-fault loop or equivalent protective-device verification, RCD operation where provided, functional switching and confirmation that the faceplate is securely fitted.

This socket should only be used where its enclosure rating and the applicable location rules permit. Kitchens and other areas near water require suitable positioning and circuit protection. Bathrooms and outdoor locations may require accessories with specific IP ratings, supplementary safety measures and 30 mA RCD protection. Do not install this standard indoor socket where it may be exposed to rain, water spray, condensation or excessive dust unless an approved protective enclosure is used.

Yes, the protective earth terminal must be connected to an effective earthing conductor in accordance with the approved wiring design. RCD or RCBO protection may also be required for socket-outlet circuits under current local regulations, particularly in residential, wet-area or outdoor-related applications. The electrician should select and verify the protective device for the specific circuit.

Yes, the BL227-G is suitable for new construction, renovation and interior fit-out work where a classic grey, double 13A switched socket is specified. Contractors should coordinate the socket locations, mounting heights, wall-box installation, circuit schedules and finish approvals with the MEP drawings, architectural layouts and consultant requirements.

It should not automatically be selected for fixed or high-load equipment. Air conditioners, water heaters, cookers and similar appliances may require dedicated circuits, double-pole isolators, fused connection units or higher-rated outlets. A qualified electrical engineer or electrician should check the appliance current, starting load, cable size and manufacturer instructions before connection.

The classic grey finish works well with contemporary offices, apartments, villas, hospitality interiors, exposed concrete effects and darker decorative palettes. For consistent project presentation, confirm the approved colour sample and coordinate it with other ABB Inora switches, sockets and electrical accessories before bulk installation.

Isolate the supply before inspection or maintenance. Clean the faceplate with a soft, dry or lightly damp cloth and avoid solvents, abrasive cleaners and direct water spray. Arrange inspection by a qualified electrician if there is overheating, discoloration, cracking, loose plug retention, unusual noise, arcing or inconsistent switch operation.