ABB Inora 2 Gang 13A Single Pole Switched Socket Outlet Starry Black BL227-885

The 13A rating indicates the nominal current rating of the socket outlet. SP means single pole, where each switch controls the live conductor to its corresponding outlet. Double switched means the unit has two outlets, each with its own on-off switch. The circuit loading must always remain within the limits specified by the electrical design, protective device and applicable installation regulations.

This type of 13A switched socket is commonly used in UAE residential and commercial developments that specify British-style socket systems. Before installation, the contractor should verify the product documentation, plug format, project specification and approval requirements of the relevant UAE authority, consultant or developer. Compliance should not be assumed solely from the socket rating or appearance.

It is suitable for indoor power points in villas, apartments, offices, hotels, retail units and similar buildings. Typical applications include bedrooms, living areas, workspaces and other dry internal locations. Suitability for kitchens, utility rooms or locations near water depends on the installation zone, enclosure protection, circuit protection and local electrical requirements.

Installation should be completed by a qualified electrician. The circuit must first be isolated, locked out where required and tested to confirm it is de-energised. The electrician should check the back box depth and alignment, terminate the live, neutral and earth conductors at the correctly marked terminals, tighten connections to the manufacturer's specified torque, secure the socket evenly and complete polarity, earth continuity, insulation and functional tests before energising.

Contractors should confirm the model number BL227-885, Starry Black finish, required quantity, socket and plug configuration, back box compatibility, terminal capacity and project-approved manufacturer schedule. They should also review the ABB technical data sheet and any consultant, developer, ADDC, DEWA, SEWA or other relevant authority requirements applicable to the project location.

Yes, both outlets can generally be used simultaneously, with each outlet controlled by its own switch. However, the combined connected load must not exceed the capacity of the final circuit, cable, protective device or installation design. High-load appliances should only be connected where the circuit has been specifically designed and approved for them.

Yes. The Starry Black finish provides a contemporary appearance that coordinates well with dark joinery, stone finishes, feature walls, modern office fit-outs and premium residential interiors. For a consistent result, architects and contractors should verify the finish against approved samples and coordinate it with other ABB Inora wiring accessories used in the project.

It should not be treated as an outdoor or weatherproof socket unless ABB documentation specifically confirms an appropriate IP rating and installation method. UAE outdoor conditions can expose accessories to dust, moisture, heat and UV radiation. Outdoor applications normally require a suitably rated weatherproof enclosure or a dedicated outdoor socket selected for the environmental conditions.

Installation in bathrooms, wash areas or other wet locations is subject to strict zoning and protection requirements. A standard indoor socket should not be installed in a wet area unless its location, ingress protection, RCD protection and installation method comply with applicable UAE regulations and the approved electrical design. A qualified electrician or project consultant should assess the location.

The socket circuit should use correctly sized conductors and an appropriately rated protective device selected by the electrical designer. RCD or RCBO protection may be required depending on the installation type and applicable UAE authority or project standards. Proper earthing, polarity and fault-loop conditions must also be verified through electrical testing before handover.

Switch off and isolate the circuit before inspection or maintenance. Clean the visible surface with a soft, dry or lightly damp cloth and avoid abrasive pads, solvents and aggressive chemicals that may damage the finish. If there is overheating, discoloration, cracking, a loose faceplate, buzzing or intermittent operation, stop using the outlet and have it inspected by a qualified electrician.

Yes, it can be specified for both new builds and interior renovation projects where a 13A double switched socket in Starry Black is required. During refurbishment, the electrician should inspect the existing wiring, earthing, protective devices and mounting box rather than assuming they are suitable. On larger projects, an approved sample and coordinated wiring-accessory schedule help maintain finish consistency.

The ABB Inora BL227-885 combines two independently switched outlets with a modern Starry Black finish, making it useful where functionality and interior coordination are both important. ABB is widely recognised in electrical and construction markets, but project acceptance should still be based on the exact product documentation, required certifications, approved material submittal and local authority requirements.