ABB Inora 1 Gang 13A Single Pole Switched Socket Outlet with Red Rocker and Illumination Classic Grey BL213-G

SP means single pole. The switch controls the live conductor to the socket outlet, while the neutral conductor remains connected. Correct polarity and earthing are essential, so the socket should be wired and tested by a qualified electrician in accordance with the approved electrical design and applicable UAE requirements.

The red rocker provides strong visual identification of the socket switch. This can be useful where a controlled outlet must be distinguished from standard sockets, such as for dedicated appliances, maintenance equipment, plant-room accessories or other designated circuits. The red rocker does not, by itself, confirm an emergency, UPS or fire-alarm function; the circuit must be labelled according to the project specification.

The 13A switched-socket format is widely used in UAE buildings with nominal 230V, 50Hz electrical systems. Suitability for a specific project depends on the approved drawings, load requirements, socket and plug standard, local authority regulations and consultant specifications. Confirm the product's compliance documentation and required approvals before using it in DEWA, ADDC, SEWA or other authority-regulated projects.

Yes, it can be considered for permanent indoor electrical installations in villas, apartments, offices, retail units, workshops and service areas where a 13A single switched outlet is specified. It should not be treated as a temporary site-power socket unless the complete installation, enclosure, protection and environmental rating are suitable for construction-site conditions.

First isolate and lock out the circuit, then verify that it is de-energised with an approved tester. Install a compatible back box, prepare the conductors without damaging them, and connect live, neutral and earth to the correctly marked terminals. Tighten terminals to the manufacturer's specified torque, secure the socket without trapping cables, align the faceplate and restore power only after inspection and electrical testing. Installation should be completed by a licensed or qualified electrician.

Use a back box and mounting arrangement compatible with the ABB Inora single-socket format and the wall construction. The box must provide sufficient depth for conductors, terminals and safe cable bending. Confirm compatibility with the project's flush or surface-mounted system, conduit entries, cable size and earthing arrangement before installation.

The socket circuit should have correctly rated overcurrent protection and residual-current protection where required by UAE regulations, the relevant wiring rules and the project design. Cable size, circuit arrangement, breaker rating, earth-fault protection and maximum demand must be selected by the electrical designer or contractor rather than based only on the socket's 13A rating.

Only equipment fitted with a compatible plug and operating within the socket, circuit and protective-device ratings should be connected. High-starting-current tools, heaters and other continuous heavy loads require a load assessment. Industrial machinery, large air-conditioning equipment and high-power construction equipment may require dedicated industrial sockets, isolators or hardwired supplies instead.

Do not assume that this standard wiring accessory is weatherproof. For outdoor areas, wash-down zones, bathrooms, gardens or dusty construction environments, use an appropriately IP-rated enclosure or a purpose-built weather-resistant socket selected for the location. Installation must also comply with the required electrical zones, RCD protection and local safety regulations.

Position it according to approved electrical layouts, accessibility requirements, furniture plans and the equipment it will serve. Maintain required separation from water, heat sources and other services. On blockwork, drywall or partition systems, ensure the back box is firmly supported, level and installed at the specified finished-wall depth before fitting the socket.

A qualified electrician should verify protective-conductor continuity, insulation resistance, polarity, earth-fault loop conditions and the operation of applicable protective devices. The rocker and socket should also be checked mechanically and functionally. Test results should be recorded as part of the project's inspection, testing and handover documentation.

Keep the faceplate clean and dry, and inspect it periodically for cracks, heat discolouration, loose mounting, sparking sounds or an unusually warm surface. Do not spray cleaner directly into the outlet. If damage or overheating is observed, isolate the circuit and arrange inspection by a qualified electrician; terminals should never be tightened while energised.

Check the model number BL213-G, 13A rating, single-pole switching requirement, single-outlet configuration, red rocker and Classic Grey finish against the bill of quantities, approved material submittal and electrical drawings. Also confirm back-box compatibility, required certifications and authority or consultant approval before ordering for a UAE construction project.