ABB Inora 2 Gang 1 Way 20AX Switch Royal Gold BL114-PG

Two gang means the switch has two separate controls on one faceplate. One way means each circuit is operated from a single switching location, unlike a two-way arrangement that allows control from two locations. The 20AX designation identifies the switch rating for AC loads and indicates suitability for loads with higher switching inrush, subject to the connected equipment, circuit design and ABB technical requirements.

Yes. Each rocker is intended to switch an independent circuit, allowing two lighting groups or other compatible loads to be controlled separately. For example, one rocker may operate ceiling lights while the other operates wall lights. Both circuits must be correctly designed, protected and kept within the switch and connected-load ratings.

It may be used with compatible LED lighting circuits, but the electrician must check the LED driver's inrush current and the total connected load rather than relying only on the lamps' nominal wattage. Multiple LED drivers can create a high startup current that affects switch selection. Refer to ABB's technical documentation and the luminaire or driver manufacturer's specifications before finalising the circuit.

The product is relevant to UAE villas, apartments, hotels, offices and retail fit-outs that use compatible wall-box and wiring arrangements. UAE low-voltage supplies are typically 230 V AC at 50 Hz, but compatibility and compliance must be confirmed for the specific project. Installation should follow current UAE regulations, the requirements of the relevant local authority or utility, approved project specifications and applicable wiring standards such as BS 7671 where adopted.

Installation should be completed by a qualified electrician. The circuit must first be isolated at the distribution board, locked off where required and tested to confirm it is dead. The electrician should identify the incoming live conductor and the two switched-live conductors, terminate them according to ABB's terminal markings and instructions, secure the mechanism in a compatible flush or surface box, fit the faceplate and test polarity, insulation, earth continuity and switching operation before energising.

A conventional mechanical one-way switch normally interrupts the live conductor and generally does not require a neutral connection for its switching function. However, the actual wiring arrangement must follow the terminal diagram supplied with the product and the approved circuit design. Neutral conductors should never be connected to switch terminals unless expressly required by the manufacturer's instructions.

Use a wall box and mounting arrangement that match the ABB Inora accessory dimensions, fixing centres and installation instructions. The box must also provide sufficient depth for safe conductor bending and termination without crushing the wiring. Before procurement for a construction project, verify compatibility with the selected ABB Inora plates, modules, conduits, cable sizes and flush-box system.

Not by itself. A one-way switch is designed to control each connected circuit from one location. Staircases, long corridors and rooms requiring control from two positions normally need suitable two-way switches, while control from three or more positions may require intermediate switching. The electrician should select the correct switching configuration during the electrical design stage.

It should only be used where the load type, running current and startup current are compatible with the switch manufacturer's rating. Fans, motors, pumps and some electronic equipment can produce inductive or high-inrush currents and may require a dedicated isolator, contactor or appropriately rated control device. An electrical engineer or qualified electrician should assess the application before connection.

Yes. The royal gold finish is well suited to premium villas, majlis interiors, hotel rooms, reception areas, executive offices and luxury retail spaces. For a coordinated result, designers and contractors should use matching ABB Inora accessories throughout visible areas and protect the finish from cement slurry, paint, abrasive cleaners and sharp tools during construction and handover.

Do not assume that a decorative indoor wall switch is weatherproof. Outdoor, wet-area and bathroom installations require appropriate ingress protection, safe zoning and compliance with local electrical regulations. If the location is exposed to water, dust, humidity or direct sunlight, use a suitably IP-rated enclosure or a purpose-designed weatherproof switch approved for that environment.

The contractor should confirm secure mounting, correct conductor identification, tight terminations, proper circuit protection and smooth independent operation of both rockers. Required electrical tests should be completed and recorded, including continuity, insulation resistance, polarity and functional testing as applicable. The faceplate should also be inspected for scratches, gaps, misalignment or construction residue before project handover.

Isolate the circuit before inspection or maintenance. Wipe the faceplate gently with a soft, dry or lightly damp cloth, and avoid abrasive pads, solvents, acidic chemicals or strong construction cleaners that may damage the royal gold finish. If the switch becomes loose, warm, noisy, discoloured or intermittent, stop using it and arrange inspection by a qualified electrician.

This model combines two independent controls in one wall position, a 20AX switching designation and a decorative royal gold appearance from ABB. It is a practical choice for contractors and interior fit-out teams seeking coordinated electrical accessories for UAE residential and commercial projects. Final selection should always be checked against the approved material schedule, load calculations, authority requirements and ABB product documentation.