ABB Inora 2 Gang RJ45 Cat 5e Data Outlet Starry Black BL332-885

When correctly terminated as part of a complete standards-compliant Category 5e channel, the socket can support common Ethernet applications including 10BASE-T, 100BASE-TX and 1000BASE-T. Actual speed depends on the cable category, patch panels, patch cords, active network equipment, termination quality and total channel length.

Yes, its 2 gang configuration is intended to provide two CAT.5e data connection points at one wall location. This is useful where separate wired links are required for devices such as computers, IP phones, smart televisions, printers, access points or building-management equipment.

It is suitable for indoor structured-cabling installations in residential villas, apartments, commercial offices, retail units, hospitality properties and other buildings. Typical locations include workstations, meeting rooms, reception areas, television points, study rooms and networked equipment positions.

Route the specified CAT.5e cable to the wall box, maintain the cable bend radius and avoid excessive pulling force. Terminate each conductor on the corresponding data module using the same T568A or T568B wiring scheme adopted throughout the project. Fit the assembly securely into a compatible mounting box, attach the Starry Black faceplate and label both data outlets. Installation should be completed by a qualified ELV or structured-cabling technician.

Either scheme may be used if supported by the socket's termination markings and project specification, but the same scheme must be applied consistently at both ends of every cable run. T568B is common in many structured-cabling projects, although the consultant-approved design and existing network convention should always take priority.

Use genuine four-pair Category 5e cable that matches the project's fire, shielding and installation requirements. All channel components should have compatible category and shielding classifications. Using lower-category cable, mismatched shielded and unshielded components, damaged conductors or poor-quality patch leads can reduce performance.

A conventional structured-cabling channel is normally limited to 100 metres, typically comprising up to 90 metres of permanent horizontal cable plus patch cords and equipment cords. Project designers should verify the final layout against ISO/IEC 11801, ANSI/TIA-568 requirements and the network equipment manufacturer's instructions.

The data outlet should be included in the ELV and structured-cabling layout before wall finishing begins. Provide the correct mounting box and conduit, coordinate outlet positions with furniture and equipment, and maintain suitable separation from mains power cables to reduce interference and comply with the project's electrical and ELV specifications. Cross power cables at approximately 90 degrees where unavoidable.

Yes, it is relevant to UAE residential and commercial projects requiring dependable fixed Ethernet points and a contemporary dark finish. The complete installation should follow approved project specifications, applicable UAE authority requirements and recognised structured-cabling practices such as ISO/IEC 11801 or ANSI/TIA-568. Fire-rated or low-smoke cable requirements should be confirmed for the specific building and authority approval.

A correctly installed CAT.5e link may carry Power over Ethernet for compatible devices such as IP phones, cameras and wireless access points. Suitability depends on the PoE standard, cable construction, conductor quality, bundle size, ambient temperature and connected equipment. For higher-power PoE applications, confirm the complete channel rating and consultant requirements before installation.

Each outlet should be checked for correct wire map, continuity, split pairs, shorts and open circuits. For construction handover, a calibrated cable certifier should be used where CAT.5e performance certification is required. Label both ends of each run and retain test reports as part of the structured-cabling as-built documentation.

The Starry Black finish is well suited to contemporary UAE interiors, dark wall features, hospitality spaces and modern office fit-outs. Before ordering multiple units, coordinate the finish with other ABB Inora switches, sockets and accessories to maintain a consistent appearance across the project.

This type of data socket is generally intended for indoor use unless installed within a suitably rated weatherproof enclosure. For outdoor, dusty, humid or wash-down areas in the UAE, select an enclosure with an appropriate IP rating and use UV-resistant or outdoor-rated cable as required by the site conditions.

Routine maintenance is minimal. Keep the outlets clean and dry, avoid inserting damaged plugs, and inspect them if network connections become intermittent. Clean the faceplate with a soft, lightly damp cloth without abrasive cleaners or solvents. Any loose termination or damaged module should be checked by a qualified network technician.