ABB Inora 2 Gang RJ45 Cat 6 Data Outlet Starry Black BL329-885

When installed as part of a correctly designed Category 6 channel using compatible CAT6 cable, patch panels and patch cords, the socket is suitable for Ethernet data, IP telephony, network printers, smart televisions, access points, CCTV systems and building-automation devices. Actual network speed and performance depend on the complete cabling channel, cable length, termination quality and connected equipment.

For this product, 2 gang indicates that the outlet provides two data connection positions in a single faceplate assembly. This allows two compatible network devices or cable runs to be connected at one wall location, reducing the need for separate outlets and helping create a neat structured-cabling layout.

Yes, it is relevant to residential, commercial and fit-out projects across the UAE where fixed Ethernet outlets are required. Its Starry Black finish suits contemporary interiors, while the two-port configuration is practical for workstations, television areas, meeting rooms and security-system points. The complete installation should comply with the project specifications, local authority requirements and applicable UAE electrical, fire-safety and low-voltage cabling regulations.

Typical locations include office desks, meeting rooms, reception areas, hotel rooms, apartments, villas, retail counters, control rooms and entertainment walls. In construction projects, data points should be planned near the equipment they serve while maintaining the required separation from electrical power wiring and sources of electromagnetic interference.

Installation should be completed by a qualified ELV or structured-cabling technician. Isolate nearby electrical circuits, route the CAT6 cable without excessive pulling or tight bends, prepare the conductors carefully, and terminate both ends using the same T568A or T568B wiring scheme specified for the project. Preserve the cable-pair twists as close as practical to the termination, secure the outlet in a compatible mounting box, fit the faceplate correctly and label each port.

Either T568A or T568B may be used if supported by the outlet termination and project specification, but the same scheme must be maintained at both ends of each cable link. T568B is frequently encountered in commercial networks, although contractors should always follow the consultant-approved structured-cabling schedule and the termination markings supplied with the product.

Use genuine Category 6 cable and compatible components throughout the channel, observe the specified maximum cable lengths, avoid crushing or sharply bending the cable, and do not untwist conductor pairs more than necessary at the termination. Keep data cables separated from power cables according to the applicable standards and project requirements. Every completed link should be tested with an appropriate cable tester, with certification testing used where required by the consultant.

A data outlet may be positioned in the same workstation or room as electrical outlets, but the data and power cabling must be routed and segregated correctly. Contractors should use suitable containment, partitions or separate boxes where required and follow local regulations, consultant drawings and recognized structured-cabling practices. Proper separation helps reduce interference and improves safety and network reliability.

Yes, it can be used as a fixed network termination point for compatible IP CCTV cameras, network video recorders, smart-home controllers, Wi-Fi access points and other Ethernet-enabled devices. If Power over Ethernet is required, confirm that every component in the channel, including the cable, connectors, patch panel and active network equipment, is appropriately specified for the intended PoE load.

This type of decorative data socket is generally intended for protected indoor locations unless ABB documentation for the exact assembly states otherwise. For outdoor, dusty, humid or wash-down environments common on some UAE sites, use a suitably rated weatherproof enclosure or an outlet with the required IP rating. Avoid direct exposure to rain, condensation, construction dust and extreme heat.

Confirm the model number BL329-885, Starry Black finish, two-port requirement, mounting-box compatibility and alignment with the other ABB Inora accessories specified for the project. Buyers should also verify whether the required data modules, termination hardware, back box and installation accessories are included or must be ordered separately, as project configurations can vary.

After termination, test each port for wire map, continuity, open circuits, short circuits, reversed pairs and split pairs. For consultant-approved or performance-critical construction projects, use a calibrated certification tester to confirm compliance with the specified Category 6 permanent-link or channel requirements. Label the outlet and retain the test report for commissioning and handover documentation.

Disconnect connected equipment and wipe the faceplate with a soft, dry or slightly damp cloth. Do not apply abrasive pads, solvents, strong chemicals or excessive water, as these may damage the Starry Black finish or enter the data ports. Keep the sockets free from construction dust and inspect terminations if network performance becomes intermittent.