ABB Inora 2 Gang RJ11 Telephone Outlet Classic Grey BL322-G

The 2 gang configuration provides two RJ11 outlets on one accessory plate. This can support two compatible telephone devices or two separately terminated communication lines, depending on the project cabling and system design. The outlets should be wired and labelled according to the approved ELV or telecommunications drawings.

The BL322-G is an RJ11 telephone socket and should not be treated as an RJ45 Ethernet outlet. RJ11 connectors are commonly used for analogue telephone, fax, modem and selected intercom applications, while computer networks generally use RJ45 outlets and structured Cat6 or Cat6A cabling. Buyers should confirm the required connector and system type before ordering.

This socket is suitable for indoor residential, commercial and hospitality applications, including villas, apartments, offices, reception areas, hotel rooms, meeting rooms and service counters. It can be installed at locations identified for telephone, fax, modem or compatible intercom connections. Suitability ultimately depends on the telecommunications system, cable specification and approved project design.

Installation should be completed by a qualified electrician or ELV technician. The installer should verify the back-box and accessory compatibility, route the approved telecommunications cable separately from power wiring where required, terminate the correct conductors at the RJ11 terminals, secure the socket without trapping the cable, fit the faceplate and test both outlets. Always follow ABB instructions, project drawings and applicable UAE requirements.

Yes. Although telephone wiring is classified as low-voltage communication wiring, an active line may carry ringing voltage. The circuit should be disconnected or made safe before termination, and installers should use suitable test equipment. Telephone cables should also be segregated from mains electrical cables in accordance with the approved design, local regulations and good ELV installation practice.

Use the telecommunications cable specified by the consultant, service provider or ELV design. Suitable twisted-pair telephone or structured communication cable may be used when its conductor size and termination method are compatible with the socket. For new UAE construction projects, the selected cable should also meet the project fire-performance, containment and authority requirements.

They may be connected to the same line only when the telephone system design, socket terminal arrangement and service provider requirements permit parallel connections. They can also be assigned to separate lines where supported. The installer should follow the approved wiring schedule and test each outlet for correct line assignment, continuity and operation.

Yes, it is relevant for UAE residential, office, retail and hospitality projects that specify RJ11 telephone connectivity and a classic grey finish. Before procurement, contractors should confirm the model number BL322-G, outlet type, accessory range, mounting arrangement and consultant approval. Installation must comply with applicable UAE authority requirements, project specifications and telecommunications provider guidelines.

Contractors should verify that the project requires a 2 gang RJ11 outlet rather than RJ45 data ports, confirm the classic grey colour, check compatibility with the selected ABB Inora plates and mounting boxes, and review cable and termination requirements. The approved material submittal, BOQ, ELV drawings and room finish schedule should be checked to prevent connector, colour or mounting mismatches.

After termination, inspect the conductors for secure and correctly assigned connections, then test continuity, polarity or pin assignment as required by the telephone system. Connect an approved telephone line tester or compatible device to each outlet and confirm dial tone, extension operation or system communication. Both outlets should be individually labelled and recorded in the project testing documentation.

Keep the socket dry and free from dust, paint and construction debris. Clean the classic grey surface with a soft, dry or slightly damp cloth and avoid abrasive cleaners or solvents. If a connection becomes intermittent, have an ELV technician inspect the plug, socket contacts, cable termination and telephone system rather than inserting tools or applying contact chemicals.

This type of telephone accessory is generally intended for protected indoor installation unless the complete assembly has a verified environmental or ingress-protection rating for the proposed location. For outdoor, wash-area or high-humidity applications, use a suitably rated enclosure and accessories approved for those conditions. Confirm the product documentation and project specification before installation.

The BL322-G combines two telephone connection points in one coordinated ABB Inora accessory, helping create an organised finish in residential and commercial interiors. The classic grey colour can complement contemporary electrical accessories, while the dual RJ11 format is practical where two compatible telephone connections are specified. Selection should remain consistent with the approved project accessory schedule.