ABB Inora Shaver Socket, 115/230V 20VA Classic Grey BL401-G

The listed model is ABB BL401-G and is identified as an AC shaver socket for a nominal 230 V supply. Because the product title contains an unclear reference to 20 V, buyers should confirm the exact input voltage, output voltage, frequency, rated load and isolation arrangement from the product label or ABB technical datasheet before installation. The unit must not be energised if its marked ratings do not match the UAE electrical supply.

It may be suitable for UAE bathrooms when installed in an approved location and in accordance with its ABB documentation, the applicable UAE electrical regulations and the project specifications. Bathroom electrical installations require careful consideration of wet-area zones, socket positioning, earthing, protective devices and water exposure. Approval should be obtained from the project consultant or relevant local authority where required.

Use it only with low-power personal-grooming equipment that is compatible with the socket's marked voltage, outlet configuration and maximum load. Some rechargeable toothbrushes may be compatible, but this must be verified from both manufacturers' instructions. It must not be used for hair dryers, hair straighteners, kettles, heaters, cleaning machines or other high-load appliances.

Many purpose-built bathroom shaver supply units use an isolating transformer, but this feature should not be assumed solely from the product name. Check the markings and official ABB datasheet for confirmation of transformer isolation, thermal protection, outlet ratings and permitted duty cycle. A qualified electrician should verify that the selected unit meets the bathroom design requirements.

Installation should be completed by a licensed electrician. The circuit must first be isolated and proven dead. The installer should confirm the correct mounting box and wiring arrangement, connect line, neutral and earth where specified, secure all terminals to the manufacturer's recommended torque, fit the socket level with the finished wall, and test the completed circuit before energising it. ABB installation instructions and local authority requirements take priority.

During first-fix work, provide a compatible concealed or surface mounting box, suitable conduit, correctly sized conductors and adequate cable access. Coordinate the outlet position with bathroom tiles, mirrors, vanity units, splash zones and MEP drawings. The box should finish flush and square with the final wall surface, with sufficient depth for the socket body and conductors without crushing or sharply bending the cables.

Circuit protection must follow the ABB instructions, the approved project design and regulations applicable in the relevant UAE emirate. Depending on the installation, this can include an appropriately rated circuit breaker, residual-current protection, effective earthing and supplementary bonding where required. The protective arrangement and disconnection times should be verified through electrical testing by a competent professional.

Position it in an accessible location near the grooming or mirror area while maintaining the required separation from baths, showers, basins and direct water spray. Exact placement depends on the wet-area classification, local regulations, manufacturer restrictions and approved drawings. It should not be installed where condensation, cleaning jets or plumbing leaks can enter the device.

The classic grey finish works well with contemporary tiles, stone surfaces, grey accessories and modern bathroom interiors. It is suitable for villas, apartments, hotels, offices and other projects where the ABB Inora wiring-accessory design has been specified. Confirm finish samples and compatibility with adjacent switches, frames and plates before ordering for a large project.

Replacement is possible only after checking the supply rating, mounting-box dimensions, terminal arrangement, wall opening, circuit protection and permitted bathroom location. The existing circuit should be inspected for damaged conductors, overheating, loose connections and moisture ingress. Do not assume that another brand's box, frame or wiring configuration will be directly compatible.

The electrician should verify supply voltage, polarity, protective-conductor continuity where applicable, insulation resistance, circuit protection and secure termination. The socket should also be checked for correct operation, excessive heat, abnormal noise, physical damage and firm mounting. Record test results as required by the project's inspection and commissioning procedures.

Keep the faceplate clean and dry, using a soft cloth without abrasive or solvent-based cleaners. Periodically inspect it for cracks, looseness, discoloration, buzzing, overheating or moisture. Stop using the outlet and isolate the circuit if any defect is found. Internal inspection, repair or replacement must be performed by a qualified electrician.

Confirm the model number BL401-G, classic grey colour, exact input and output ratings, plug compatibility, maximum load, isolation features, mounting-box requirements and included components. Project buyers should also verify consultant approval, local authority compliance and compatibility with the selected ABB Inora range. Checking these details prevents voltage, installation and finish mismatches on site.