ABB Millenium 13A Double Pole Double Switched Socket with LED Dune Sand AM240147-DU

Key specifications include a rated current of 13A, rated voltage of 250V AC, 2-gang dual BS 13A socket configuration, double-pole switched operation, integrated LED indication and flush-mounted installation. The listed overall dimensions are approximately 42 x 147 x 86 mm; the back-box and cut-out requirements should be checked against the ABB installation documentation before installation.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than single-pole switching and is useful for connected appliances and circuits where reliable disconnection is required. The protective earth remains permanently connected and must never be switched.

This is described as a double switched, 2-gang socket, indicating switched control for the two socket outlets. The exact switch and LED operating arrangement should be confirmed from the product markings and ABB wiring diagram supplied with the unit before termination, particularly when preparing project schedules or matching an existing Millenium installation.

The integrated LED provides a visible indication of the switch or connected-circuit status, helping users identify whether the outlet is operating. The precise LED behavior can depend on the internal configuration, so installers should follow the ABB wiring diagram rather than assuming that the LED indicates the presence or absence of voltage under every condition.

Its 250V AC rating and BS-style 13A socket format are compatible with the electrical supply and Type G plug system commonly used in the UAE. Suitability for a specific project must still be confirmed against the applicable authority requirements, approved material schedule, project specification and relevant UAE electrical installation regulations.

It is suitable for indoor fixed electrical installations such as villas, apartments, offices, hotels, retail units and other commercial interiors. The Dune Sand finish is particularly useful where wiring accessories must coordinate with warm neutral walls or ABB Millenium design schemes. It should not be installed outdoors, in wet areas or in dusty construction environments unless the completed assembly has the required enclosure and IP protection for that location.

Installation should be completed by a qualified electrician. Isolate and verify the circuit as dead, confirm the compatible flush back box and cable capacity, prepare the conductors without damaging them, and connect live, neutral and protective earth to the clearly marked terminals in accordance with the ABB wiring diagram. Tighten terminals to the manufacturer's specified torque, arrange conductors without trapping or excessive bending, secure the socket and matching frame, then carry out the required electrical tests before energising the circuit.

A compatible concealed back box must provide the correct mounting centres, opening dimensions and sufficient internal depth for the socket body, terminals and conductor bending radius. Because the listed product dimensions do not by themselves define the required back-box depth, contractors should check the ABB Millenium technical drawing and allow additional space where larger cables or multiple conductors are terminated.

Cable size, circuit arrangement, MCB or RCBO rating and RCD protection must be selected from the circuit design rather than from the socket rating alone. The electrician should consider connected load, installation method, ambient temperature, grouping, voltage drop, fault current and local authority rules. In UAE projects, follow the applicable electricity distribution authority regulations and the project requirements, with BS 7671 principles where specified or adopted.

It may supply compatible appliances only when the appliance load, plug, socket and complete final circuit are within their approved ratings. Do not exceed the marked 13A rating or assume that the presence of two outlets increases the permitted circuit load. Continuous or high-demand equipment should be checked against the circuit design, manufacturer instructions and local installation requirements.

Use in kitchens or utility areas depends on its position, the applicable zone restrictions and the protection provided by the circuit and enclosure. No specific IP rating is stated in the supplied product data, so it should not be treated as weatherproof or splashproof. For bathrooms, balconies, gardens, outdoor kitchens or exposed locations, select a suitably IP-rated accessory and follow UAE authority and project requirements.

Confirm the model number AM240147-DU, Dune Sand colour, 2-gang layout, 13A and 250V AC ratings, double-pole switched configuration, LED requirement and flush-mounting compatibility. Also verify the matching ABB Millenium frame, back box, project-approved finish, quantities and any required conformity documentation before procurement.

Before handover, the electrician should perform the tests required by the applicable UAE authority and project specification. These normally include protective-conductor continuity, insulation resistance, polarity, earth-fault loop or equivalent protective-device verification, and RCD or RCBO testing where fitted. The switches, LED indication and both socket outlets should also be functionally checked, with results recorded in the installation test documentation.

Switch off or isolate the supply before inspection or cleaning. Wipe the faceplate with a soft, dry or slightly damp cloth and avoid abrasive pads, solvents and aggressive chemicals that could damage the finish. Periodically check for heat discoloration, cracking, loose mounting, unusual odor or intermittent operation; any defect should be investigated by a qualified electrician rather than repaired while energised.