ABB Millenium 13A Double Pole Double Switched Socket with LED Matt Gold AM240147-MG

Key specifications include a 13A rated current, 250V AC rated voltage, dual BS 13A socket outlets, double-pole switching, LED status indication and flush-mounted installation. Its stated dimensions are approximately 42 x 147 x 86 mm. Terminal capacity, back-box requirements and conductor sizes should be confirmed from the ABB installation instructions before fitting.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than single-pole switching. The protective earth remains permanently connected and must never be switched or omitted.

Its BS-type 13A outlet format and 250V AC rating are relevant to the plug and socket system commonly used in the UAE. Suitability for a specific project must still be checked against the approved electrical design, local authority requirements and applicable regulations from bodies such as DEWA, ADDC or the relevant emirate authority. Installation should be completed and tested by a licensed electrician.

It is intended for compatible BS 13A plug-connected equipment within the designed circuit capacity, such as televisions, computers, chargers and many domestic or office appliances. High-load equipment must be checked against the appliance rating, plug fuse, socket rating and final circuit design. The two outlets do not automatically provide 13A each beyond the safe capacity of the connected circuit.

The integrated LED provides a visible indication of the switch or connected-circuit status, helping users identify the operating condition at a glance. The exact indication logic can depend on the product's internal configuration, so the ABB wiring diagram and installation instructions should be consulted rather than assuming whether the LED shows supply available or socket switched on.

The socket is designed for flush mounting, with the fixed wiring and compatible back box concealed behind the finished wall. The electrical supply must be isolated and proven dead before work begins. A licensed electrician should verify the back-box size and depth, prepare the conductors without damaging them, connect live, neutral and earth to the marked terminals, tighten terminals to the specified torque, secure the accessory level and test polarity, continuity, insulation resistance and protective-device operation.

Contractors should confirm the approved outlet location, finished wall level, compatible back-box dimensions, cable entry position, conductor size, circuit protection and available mounting depth. The box should be rigid, square and clear of plaster, tile adhesive and debris. Adequate space must be maintained so conductors are not sharply bent, trapped or compressed behind the socket.

Yes, it may be incorporated into blockwork, gypsum-board partitions or tiled finishes when a compatible flush box and suitable fixing method are specified. For blockwork, the box should be securely embedded and aligned with the final plaster level. For drywall, an approved cavity box is required. On tiled walls, accurate setting-out and careful cutting help protect the tile and maintain an even matt gold finish.

Yes. Its decorative matt gold finish and concealed installation suit villas, apartments, hotel rooms, executive offices, reception areas and other premium interiors. Designers and contractors should coordinate the socket finish with matching ABB Millenium frames and accessories and confirm that the selected model is included in the project's approved material schedule.

No outdoor or ingress-protection rating is provided in the listed product data, so it should be treated as an indoor accessory for dry locations unless ABB documentation confirms otherwise. Bathrooms, kitchens near water sources, balconies, gardens and external walls may require an appropriately rated weatherproof accessory, suitable enclosure, RCD protection and installation in accordance with local electrical regulations.

The socket must be supplied from a correctly designed final circuit with suitable overcurrent and residual-current protection where required by the applicable UAE regulations and project specification. Protective-device rating, cable size, circuit arrangement and maximum demand must be determined by the electrical designer or licensed contractor; the socket's 13A rating must not be used as the sole basis for circuit design.

Before energisation, the electrician should inspect conductor identification, earth continuity, terminal tightness, polarity, cable condition and mounting security. The completed circuit should undergo the tests required by the approved inspection and testing procedure. The LED and both switching functions should also be checked under safe operating conditions, with results recorded in the project handover documentation.

Isolate the circuit before cleaning and use a soft, dry or lightly dampened cloth. Do not spray liquid directly onto the socket or use abrasive pads, solvents, acidic cleaners or strong construction chemicals, as these may damage the matt gold finish or enter the electrical mechanism. During construction, protect the accessory from paint, plaster, grout, dust and impact, then remove protection carefully at handover.

The ABB Millenium AM240147-MG combines two BS-format 13A outlets, double-pole local isolation, LED status indication, concealed wiring and a coordinated matt gold appearance. These features make it a practical specification option for UAE residential, hospitality and commercial fit-outs where electrical functionality, visible operating status and a premium interior finish are required.