ABB Millenium 13A Double Pole Single Switched Socket Silk Black AM23786-SB

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than a single-pole switch, although it does not replace circuit isolation at the distribution board before electrical installation or maintenance.

Yes, its 250V AC rating and BS 13A socket format suit the supply and plug systems commonly used in the UAE. The complete installation must still comply with the relevant emirate's electricity authority requirements, approved project specifications, and applicable wiring regulations. A UAE-licensed electrician should confirm circuit protection, earthing, cable size, and product approval requirements for the specific project.

It can supply compatible equipment fitted with a BS-type 13A plug, including televisions, computers, chargers, small kitchen appliances, office equipment, and many common household devices. The connected load must not exceed the socket's 13A rating or the limits of the plug, cable, protective device, and circuit. High-load or permanently connected equipment may require a dedicated circuit or connection unit.

The socket is rated for a maximum current of 13A at up to 250V AC. At 250V, 13A corresponds to a theoretical load of approximately 3.25kW; at a nominal 230V supply, it is approximately 2.99kW. Actual permissible loading depends on the appliance, circuit design, installation conditions, cable capacity, and protective device, so the 13A rating must never be exceeded.

The socket is intended for flush mounting in a compatible concealed wall box. After safely isolating and verifying the circuit is dead, a qualified electrician should connect the live, neutral, and protective earth conductors to the correctly identified terminals, tighten them to the manufacturer's specified torque, secure the mechanism without trapping cables, fit the matching frame, and complete electrical safety testing before energising the circuit.

The product measures approximately 35 x 86 x 86 mm and has an 86 mm face width. A compatible flush box with sufficient internal depth is required to accommodate the mechanism, conductor bend radius, and terminal connections without compression. The installer should verify ABB Millenium frame and box compatibility before cutting walls or ordering boxes for a construction project.

Yes, it can be used in drywall partitions, masonry blockwork, or concrete walls when installed with the appropriate compatible flush box and fixing method. For blockwork and concrete, conduits and boxes should be positioned before plastering or finishing. For drywall, use a secure cavity box or project-specified support system and maintain the required wall and fire-performance details.

Yes, the socket has terminals intended for dependable fixed-wiring connections when conductors are correctly prepared, inserted, and tightened. Cable type and conductor size must be selected according to the circuit design and applicable regulations. Loose strands, exposed copper, overtightening, and multiple conductors in a terminal not approved for that arrangement should be avoided.

Use in kitchens should follow the required separation from sinks, heat, moisture, and splash zones. Bathrooms and outdoor locations require additional consideration of electrical zones, RCD protection, enclosure ingress protection, and local regulations. Because no specific IP rating is stated in the supplied product data, it should not be assumed suitable for exposed wet, dusty, or outdoor locations without an approved protective enclosure and confirmation from the project consultant or electrician.

Circuit protection must be designed by a qualified electrician according to the cable size, circuit arrangement, prospective fault current, connected load, and local authority requirements. Suitable overcurrent protection, effective earthing, and RCD or RCBO protection should be provided where required. The socket's double-pole switch offers local control but does not replace these protective measures.

Before handover, the installer should perform the tests required for the project and applicable wiring rules. These normally include protective-conductor continuity, insulation resistance, polarity, earth-fault loop or equivalent fault-protection verification, RCD operation where fitted, functional switching, and confirmation that the socket is securely mounted and correctly labelled where necessary.

Yes, it is suitable for consideration in offices, apartments, villas, hotels, retail interiors, and other commercial fit-outs requiring a premium flush-mounted 13A switched socket. Contractors should confirm that model AM23786-SB, the Silk Black finish, associated frame, technical submittals, and authority approvals match the consultant's specification and approved material schedule before bulk procurement.

Clean the faceplate with a soft, dry or slightly damp cloth after isolating the circuit if necessary. Do not use abrasive pads, solvents, strong chemicals, or excessive water. During construction, protect the socket from paint, plaster, cement dust, impact, and metal debris, and remove temporary protection carefully before testing and handover.