ABB Millenium 13A Double Pole Switched Socket with LED Mocha Brown AM23886-MO

The socket is rated at 13A and 250V AC and uses a BS 13A socket-outlet connection. It features double-pole switching, LED status indication, secure cable terminals and flush-mounted installation. Its stated dimensions are approximately 35 x 86 x 86 mm, so the mounting box depth and available wiring space should be checked before installation.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than a single-pole design, although it does not replace circuit isolation at the distribution board before electrical installation, inspection or maintenance.

Yes, its 250V AC rating and BS 13A socket format are suitable for the 230V, 50Hz electrical system and Type G plug format commonly used in the UAE. The complete installation must still comply with applicable UAE electrical regulations, project specifications and the requirements of the relevant local authority, such as DEWA, ADDC, SEWA or the authority having jurisdiction.

It can be used with compatible 13A fused Type G plugs for appliances and equipment whose current demand does not exceed the socket, plug, cable or circuit rating. Typical applications include televisions, computers, small kitchen appliances, office equipment and general indoor electrical loads. The appliance nameplate and manufacturer instructions should always be checked before connection.

The documented current rating is 13A at up to 250V AC. On a nominal 230V UAE supply, 13A corresponds to an approximate theoretical load of 2.99kW. Actual permitted loading depends on the appliance, fused plug, cable size, protective device, circuit design, ambient conditions and local regulations; the lowest applicable rating must not be exceeded.

The integrated LED provides a convenient visual indication of the socket or connected-circuit operating status. Its exact illumination behaviour depends on the product wiring configuration, so the ABB installation instructions supplied with the unit should be followed.

The unit is designed for flush installation in a compatible concealed wall box. A qualified electrician should isolate and verify the circuit as de-energised, confirm the box depth, terminate the live, neutral and earth conductors at the marked terminals, tighten connections to the manufacturer-specified torque, fit the socket and matching frame, and then perform the required continuity, polarity, insulation and functional tests before energising it.

Yes, provided a suitable flush box and installation method are selected for the wall construction. Masonry and concrete walls normally require a securely fixed concealed metal or approved plastic box, while drywall partitions require a compatible cavity box or support system. The finished box must be level, stable and deep enough for the approximately 35 mm product depth, cable bends and safe terminal clearance.

Yes. A 13A socket outlet must be connected to the circuit protective conductor through its designated earth terminal. Earth continuity, polarity and protective-device coordination must be verified by a competent electrician in accordance with the applicable UAE wiring requirements and project specifications.

It may be used in suitable dry indoor locations, but no IP rating is specified in the supplied product data. Installation near sinks, water sources, wet areas or bathroom zones requires appropriate location, ingress protection and additional protection as prescribed by local regulations. An IP-rated accessory should be selected where moisture or water exposure is expected.

It should not be installed in exposed outdoor, dusty or wet environments unless ABB documentation confirms an appropriate enclosure and IP-rated installation system. For UAE outdoor conditions, use a weatherproof socket selected for heat, dust, humidity, ultraviolet exposure and the required ingress-protection level.

Contractors should verify the approved material schedule, socket type, 13A and 250V AC ratings, double-pole switching requirement, mocha brown finish, compatible frame and flush box, circuit loading, cable size, earthing arrangement and protective device. They should also confirm compliance documentation and approval against the consultant's specification and the relevant UAE authority requirements before procurement.

The product uses a BS 13A socket-outlet format intended for compatible fused Type G plugs, which are widely used in the UAE. Other plug types should not be forced into the outlet or used with unapproved adaptors. For imported equipment, use a properly rated and compliant plug or adaptor recommended for the appliance.

Keep the faceplate clean and dry, and wipe it only with a soft cloth after safely isolating power when necessary. Do not use abrasive or solvent-based cleaners. Arrange inspection by a qualified electrician if the socket becomes hot, discoloured, loose, cracked, noisy, produces an odour, shows intermittent LED operation or no longer grips the plug securely.