ABB Millenium 13A Single Pole Switched Socket Black Glass AM23386-BG

Before handover, a qualified electrician should complete the tests required by the project and local electrical rules. These generally include protective-conductor continuity, insulation resistance, polarity, earth-fault protection and functional switching checks. The socket should also be inspected for secure mounting, correct frame alignment and signs of damaged terminals or conductors.

The socket combines a contemporary black glass finish with concealed flush mounting and local switched control. This makes it relevant to modern UAE villas, hospitality spaces, executive offices and upscale fit-outs where electrical accessories must coordinate with dark joinery, stone surfaces, feature walls and other premium finishes.

It may replace an existing compatible 1-gang flush socket if the circuit rating, wiring condition, conductor arrangement, back-box dimensions and mounting points are suitable. Because the product has an 86 x 86 mm face and approximately 35 mm depth, the electrician should inspect the existing box and confirm adequate space before replacement.

Terminals must be tightened securely to the manufacturer's specified torque where provided. Undertightening can cause loose connections, overheating and unreliable operation, while overtightening may damage the conductor or terminal assembly. Conductors should be correctly stripped, fully inserted and checked before the faceplate is fitted.

Switch off or isolate the circuit before cleaning. Wipe the glass surface gently with a soft, dry or slightly damp microfiber cloth, then dry it to prevent streaks. Do not spray liquid directly onto the socket or use abrasive pads, blades, solvents or aggressive chemicals, as these may damage the glass finish or allow moisture to reach the electrical mechanism.

RCD or RCBO protection may be required depending on the circuit, installation location, local authority regulations and project design. The ABB socket itself does not replace protective devices at the distribution board. The electrical consultant or licensed contractor should select the required residual-current and overcurrent protection for the installation.

A 13A socket may be used on a correctly designed ring or radial final circuit where permitted by the applicable wiring rules and project specification. Circuit topology, conductor size, protective device rating, fault protection and the number of outlets must be assessed by the electrical designer or licensed electrician rather than determined from the socket rating alone.

Yes. The protective earth conductor must be correctly terminated in accordance with the terminal markings and the building's earthing arrangement. Earth continuity, polarity and circuit protection should be verified during commissioning by a qualified electrician before the socket is put into service.

The ABB Millenium AM23386-BG is a 1-gang, flush-mounted BS 13A socket outlet with an integrated single-pole switch and a premium black glass finish. Rated at 13A and 250V AC, it provides local control of a compatible connected appliance while keeping the fixed wiring concealed behind the finished wall.

Contractors should confirm the 13A load requirement, 250V AC circuit, single-pole switching arrangement, BS 13A plug compatibility, 1-gang layout, 86 x 86 mm face dimensions, back-box depth, earthing provision and coordination with ABB Millenium frames and adjacent accessories. Samples and approved finishes should also be checked against architectural schedules before procurement.

Use a compatible 1-gang concealed back box that accommodates the socket mechanism, cable bend radius and approximately 35 mm product depth. The required box depth can vary with cable size, terminal space and wall construction, so the electrician should verify compatibility before blockwork chasing, drywall closure or final finishing.

The socket is designed for flush mounting into a compatible concealed wall box. A qualified electrician should isolate and verify the circuit as dead, confirm the back-box depth and cable condition, terminate the live, neutral and earth conductors at the marked terminals, secure the mechanism without overtightening, fit the matching frame and glass finish, and then complete continuity, polarity, insulation and functional tests before energising the circuit.

Yes. Its premium black glass appearance is suitable for contemporary villas, apartments, offices, hotels, reception areas, meeting rooms and high-end interior fit-out projects. The 86 x 86 mm format and concealed installation help create a neat wall finish, subject to compatibility with the selected back box, frame and surrounding wiring accessories.

It can supply compatible appliances fitted with a BS-type 13A plug, provided the connected load remains within the socket rating and the circuit design. Typical uses include televisions, computers, lamps, chargers and suitable household or office equipment. High-load appliances should only be connected after confirming their current demand, plug fuse, cable size and circuit protection.