ABB Millenium 13A Single Pole Switched Socket White Glass AM23386-WG

The socket has a rated current of 13A, a rated voltage of 250V AC, a BS 13A socket-outlet configuration and single-pole switching. It is designed for flush mounting, measures approximately 35 x 86 x 86 mm and uses secure terminals for fixed-wiring connections. The product is supplied in a white glass finish and is intended as a single-gang outlet.

Yes, its BS 13A outlet format is widely used in UAE residential and commercial buildings, while its 250V AC rating is appropriate for circuits operating on the UAE's nominal 230V AC supply. Installation must still comply with the approved project specification, applicable UAE electrical regulations and the requirements of the relevant local authority, such as DEWA, ADDC or the authority serving the project location.

Single-pole switching means the socket's switch interrupts the live conductor to provide convenient local control of the connected appliance. It does not switch the neutral conductor and should not be treated as complete electrical isolation. The circuit must be isolated at the distribution board and verified as dead before installation, maintenance or terminal access.

It can supply compatible BS-plug-equipped appliances whose operating current and power demand remain within the socket, plug, circuit and protective-device ratings. Typical applications include televisions, computers, lamps and suitable domestic or office equipment. High-load appliances should only be connected after confirming their nameplate current, circuit design and manufacturer requirements; a dedicated circuit or connection unit may be required for some fixed or heavy-duty loads.

The outlet is rated for up to 13A at 250V AC. On a nominal 230V UAE supply, 13A corresponds to approximately 2.99kW as a simple voltage-by-current calculation, but this must not be used as the sole basis for circuit selection. Actual suitability depends on the appliance load, duty cycle, cable size, circuit protection, ambient conditions and the approved electrical design.

The unit is installed flush into a compatible wall box with the fixed wiring concealed behind the finished surface. A qualified electrician should isolate and prove the circuit dead, confirm the back-box size and depth, prepare the conductors, terminate live, neutral and earth in the marked terminals, tighten them to ABB's specified torque, secure the mechanism without trapping cables, fit the matching frame or cover and complete the required inspection and electrical testing before energising the circuit.

Use a compatible flush back box and mounting arrangement suited to the 86 x 86 mm face format and the product's approximately 35 mm overall depth. The electrician must also allow sufficient space for terminal connections, conductor bending radii and safe cable dressing. On blockwork, concrete or gypsum-board partitions, the box should be level, firmly fixed and positioned so its front edge coordinates with the final plaster, tile, stone or decorative wall finish.

Yes. It is suitable for electrical fit-out work in villas, apartments, hotels, offices and other compatible indoor projects. For new construction, coordinate the back-box position and finished-wall level before plastering or cladding. During renovation, verify that the existing box, cable condition, earthing, circuit protection and mounting centres are compatible before replacing the old outlet.

Yes. Protect the glass surface from impact, abrasive dust, cement, plaster, paint and tile adhesive during construction. Do not overtighten mounting points or force the faceplate against an uneven wall, as this can place stress on the decorative finish. After installation, clean it with a soft, slightly damp cloth and avoid abrasive pads, blades, acidic cleaners and strong solvents.

Only install it where the location, enclosure and electrical design are suitable. No ingress-protection rating is stated in the supplied product data, so it should not be assumed to be weatherproof or splashproof. Bathroom zones, wet kitchen positions, balconies and outdoor areas require specific protection, placement and often an appropriately IP-rated accessory in accordance with local regulations and the project specification.

The protective earth conductor must be correctly terminated wherever required by the socket, circuit and local wiring rules. RCD or RCBO protection should be provided where mandated by UAE authority requirements, the approved design or the type and location of the circuit. Earthing continuity, polarity, insulation resistance and protective-device operation should be tested by a qualified electrician before handover.

The specified connector type is a BS 13A socket outlet, intended for compatible UK-style fused plugs commonly used in the UAE. Do not force incompatible two-pin or other plug types into the outlet. Where an appliance has a different plug, use a properly approved solution selected for the appliance and circuit rather than an unsafe loose-fitting travel adaptor.

Contractors should confirm the model and finish, check that the faceplate is level and undamaged, verify secure mounting, inspect conductor termination and test earth continuity, polarity, insulation resistance and circuit protective devices as applicable. The switch and outlet should then be functionally tested with suitable test equipment. Test records and circuit identification should be completed in accordance with the project specification and relevant UAE authority requirements.

This ABB Millenium switched socket combines a widely used 13A BS outlet format with local load control, concealed flush wiring and a refined white glass appearance. It is particularly relevant to UAE villas, premium apartments, hotels and executive offices where electrical functionality must coordinate with contemporary interior finishes. The 1-gang layout also makes it suitable for locations requiring one controlled socket outlet rather than a multi-gang arrangement.