ABB Millenium 13A Single Pole Switched Socket with LED Silk Black AM23486-SB

Yes. Its BS 13A socket format is commonly used in UAE buildings for appliances fitted with compatible fused plugs. The 250V AC rating is appropriate for typical UAE low-voltage installations, subject to the project design and applicable authority requirements. Installation should comply with current UAE electrical regulations, the relevant emirate's authority rules, and the manufacturer's instructions.

The key specifications are a 13A rated current, 250V AC rated voltage, BS 13A socket configuration, 1-gang layout, single-pole switch, integrated LED indicator, flush-mounted installation, Silk Black finish, and approximate dimensions of 35 x 86 x 86 mm. The terminals are intended for secure fixed-wiring connections when prepared and tightened correctly.

Single-pole switching means the socket switch disconnects the live conductor while the neutral remains connected. This provides convenient local control of the connected appliance but must not be treated as complete electrical isolation. The circuit should be isolated at the distribution board and verified dead before maintenance or wiring work.

The integrated LED provides a visible indication of the switch or connected-circuit status, helping users identify whether the outlet is operating. Its exact behaviour may depend on the product's internal configuration and wiring arrangement, so the electrician should follow the ABB wiring diagram supplied with the unit.

It can supply compatible appliances using a BS 13A fused plug, provided the appliance current and total circuit load remain within the socket's 13A rating and the designed capacity of the final circuit. Typical applications include televisions, computers, lamps, small kitchen appliances, and office equipment. High-load equipment should only be connected after confirming its nameplate current and the circuit design.

Suitability depends on the equipment load, manufacturer requirements, and electrical design. Many air conditioners, water heaters, cookers, and other fixed high-load appliances require a dedicated circuit and an appropriately rated isolator or connection unit rather than a standard 13A socket. A qualified electrical engineer or licensed electrician should confirm the correct accessory and protective device.

Isolate and lock off the circuit, verify that it is dead, prepare a compatible flush mounting box, and connect the live, neutral, and protective earth conductors to the marked terminals in accordance with the ABB diagram. Tighten terminals to the manufacturer's specified torque, arrange conductors without pinching or excessive bending, secure the socket and matching frame, restore power, and complete polarity, earth-continuity, insulation, and functional tests. Installation should be performed by a qualified electrician.

The socket is designed for concealed flush mounting and has an 86 x 86 mm face size with a stated overall depth of approximately 35 mm. The selected back box must be mechanically compatible and deep enough for the device, conductors, terminations, and required bend radius. For blockwork, gypsum partitions, or decorative wall panels, the box should be level, firmly secured, and positioned flush with the final finished surface.

Yes. A BS 13A socket outlet must be connected to the circuit protective conductor through its designated earth terminal. Correct earthing is essential for shock protection and the operation of protective devices. Earth continuity, polarity, and other required electrical tests must be completed before the outlet is placed into service.

Use in kitchens or similar indoor locations depends on its position relative to water, heat, and the applicable wiring-zone requirements. It should not be installed outdoors, in wet zones, or where exposed to water, dust, or condensation unless it is housed in a suitably rated enclosure and the complete installation is approved for that environment. For external UAE applications, select weatherproof accessories with an appropriate IP rating.

Circuit protection must be selected according to conductor size, installation method, expected load, fault level, and applicable UAE or local authority regulations. The socket should be supplied from a correctly designed final circuit with suitable overcurrent protection and residual-current protection where required. The 13A marking is the outlet rating and does not by itself determine the distribution-board breaker rating.

Yes. Its flush-mounted design, 1-gang format, Silk Black finish, and LED indication suit villas, apartments, offices, hotels, retail spaces, and premium interior fit-outs. Before bulk procurement, contractors should verify compatibility with the specified back boxes, ABB Millenium frames, wiring accessories schedule, approved material submittal, and project finish sample.

Check that the faceplate is level, the frame is secure, conductors are correctly terminated, and no copper is exposed. Electrical testing should include protective-conductor continuity, insulation resistance, polarity, relevant protective-device checks, and functional operation of the switch, socket, and LED. Test results should be recorded as required by the project consultant and the relevant UAE authority.

Switch off the circuit before cleaning and use a soft, dry or lightly damp microfiber cloth. Do not use abrasive pads, solvents, strong alkaline cleaners, or excessive water, as these may damage the finish or enter the electrical mechanism. Periodic inspection by a qualified electrician is advisable if the socket becomes loose, discoloured, unusually warm, noisy, or intermittent.