ABB Millenium 13A Single Pole Switched Socket with LED Stainless Steel AM23486-ST

Yes. Its BS 13A socket configuration is compatible with the Type G fused plugs widely used in the UAE, and its 250V AC rating is suitable for the UAE's nominal 230V AC supply. Selection and installation must still comply with the project's approved specifications, applicable UAE electrical regulations, BS 7671 requirements where adopted, and the rules of the relevant authority such as DEWA, ADDC or the local electricity provider.

Single-pole switching means that the socket switch disconnects the live conductor while the neutral and protective earth remain connected. This provides convenient local control of the outlet. It is not a substitute for circuit isolation, so the distribution-board circuit must be safely isolated and verified dead before installation, inspection or maintenance.

The integrated LED provides a visible indication of the switch or connected-circuit status, making the outlet easier to identify and monitor. The precise indication can depend on the manufacturer's terminal arrangement and wiring method, so the ABB wiring diagram supplied with the product should be followed rather than assuming that the LED always indicates the presence or absence of mains voltage.

The socket is intended for compatible appliances fitted with a BS 13A fused Type G plug, subject to a maximum rated current of 13A and the capacity of the final circuit. It can serve common office equipment, televisions, computers, chargers and suitable domestic appliances. High-load equipment such as water heaters, cookers, large air-conditioning units or fixed machinery may require a dedicated circuit, isolator or connection unit specified by an electrical engineer.

Installation should be completed by a qualified electrician. The supply must first be isolated at the distribution board and proven dead with an approved tester. The live, neutral and earth conductors should then be identified, prepared and connected to the marked terminals in accordance with ABB instructions. After checking terminal tightness and earth continuity, the mechanism is secured into a compatible flush box, aligned with the finished wall and fitted with its matching frame. The circuit should be tested before energisation.

The face dimensions are approximately 86 x 86 mm, with an overall product depth of about 35 mm. Use a compatible 1-gang concealed mounting box that provides adequate internal depth for the mechanism, conductor bend radius and secure cable termination without crushing or sharply bending the wires. The exact box depth should be confirmed against the physical product, wiring arrangement and wall construction before completing blockwork, drywall or decorative finishes.

Yes. It is suitable for new-build and refurbishment work where concealed wiring and flush accessories are specified. During construction, coordinate the mounting-box position with blockwork, gypsum partitions, wall finishes, joinery and furniture layouts. Boxes should be installed level and protected from plaster, paint, dust and moisture until final fixing. The socket should only be energised after electrical testing and project inspection requirements have been completed.

Use in kitchens or other indoor locations must follow applicable zoning, RCD protection and separation requirements. The supplied information does not state an IP weatherproof rating, so the socket should not be treated as suitable for exposed outdoor, wet or wash-down locations. Outdoor installations and locations exposed to water, condensation or heavy dust require an appropriately rated weatherproof enclosure or a purpose-designed IP-rated socket selected by the project engineer.

Cable size cannot be selected from the socket rating alone. It must be determined by a qualified electrical designer or electrician based on the circuit type, protective-device rating, installation method, cable length, voltage drop, grouping, ambient temperature and UAE project requirements. Only conductor sizes and types accepted by the ABB terminal specifications should be used, and all terminations must be secure and properly tested.

Yes, the protective-earth conductor must be connected to the designated earth terminal and verified through continuity and fault-loop testing. RCD or RCBO protection should be provided where required by applicable wiring regulations, local authority rules and the installation design. The stainless-steel appearance does not remove any earthing or circuit-protection requirement.

Switch off the circuit before cleaning and wipe the surface with a soft, dry or slightly damp cloth. Do not spray liquid directly onto the socket, and avoid abrasive pads, acidic cleaners, bleach or strong solvents that could damage the finish or markings. In coastal UAE environments, regular gentle cleaning can help remove salt and dust deposits. Any heat marks, cracking, loose operation, buzzing or discoloration should be inspected promptly by a qualified electrician.

The ABB Millenium AM23486-ST combines a standard BS 13A outlet format, local single-pole control, LED status indication, concealed wiring and a stainless-steel architectural finish. These features make it relevant to villas, apartments, offices, hospitality interiors and commercial fit-outs where contractors and designers require a coordinated, flush-mounted wiring accessory from an established electrical brand.