ABB Millenium 13A Universal Switched Socket Mocha Brown AM29486-MO

Before bulk ordering, verify the model number, mocha brown colour, 1-gang configuration, 13A and 250V AC ratings, universal outlet acceptance, matching ABB Millenium frames, wall-box compatibility, required quantities, spare allowance, and consultant or authority approval. A sample installation is advisable to confirm appearance, wall-box fit, terminal space, plug compatibility, and coordination with the project's electrical and interior design specifications.

Keep the faceplate dry and clean it only with a soft, dry or slightly damp cloth after isolating power where necessary. Do not use abrasive cleaners or solvents. Periodically check for looseness, cracking, discoloration, overheating, buzzing, burning odours, or poor plug retention. In dusty, humid, or high-temperature UAE environments, inspection intervals may need to be shortened. Any damaged or overheated outlet should be isolated and examined by a qualified electrician.

The integrated switch provides convenient local isolation of the connected appliance without immediately removing its plug. This supports practical day-to-day control and can reduce wear caused by frequent unplugging. It does not replace circuit isolation, lockout procedures, or the distribution-board protective device when electrical installation or maintenance work is being performed.

It should only be installed where the environmental conditions and applicable zoning rules permit. The supplied product information does not state an IP weatherproof rating, so it should not be assumed suitable for exposed outdoor locations, wet zones, or areas subject to water spray, condensation, dust, or severe heat. Such areas may require an appropriately rated enclosure, additional protection, or a purpose-designed weatherproof socket.

Yes, it can be specified for suitable villas, apartments, offices, hotels, retail interiors, and other fit-out works where a mocha brown ABB Millenium finish is required. Contractors should coordinate the model number AM29486-MO with electrical schedules, approved material submittals, wall-box layouts, interior finishes, and consultant requirements to maintain consistency across the project.

Yes. The mechanism should be used with a compatible flush box and matching ABB Millenium frame or accessory system. The face dimensions are approximately 86 x 86 mm, with an overall listed depth of approximately 35 mm, but the installer should verify the required box depth, fixing centres, cable space, and frame compatibility before wall finishing or bulk procurement.

Appropriate verification may include visual inspection, protective-conductor continuity, insulation resistance, polarity, earth-fault loop or related protective measures, and functional testing of the switch and outlet. The exact test sequence should follow the approved project method statement, applicable wiring regulations, authority requirements, and the electrician's calibrated test procedures.

Installation should be completed by a qualified and authorised electrician familiar with UAE wiring practices and the requirements of the applicable local electricity authority. Correct polarity, earthing, conductor sizing, circuit protection, terminal tightness, and post-installation testing are essential. The socket should not be installed or rewired while the circuit is energised.

The AM29486-MO is intended for flush installation in a compatible concealed wall box. The supply must first be isolated and proved dead. The electrician should confirm box depth and alignment, prepare conductors correctly, connect line, neutral, and earth to the identified terminals, tighten connections to the manufacturer's requirements, secure the mechanism, and fit the compatible ABB Millenium frame. The circuit must then be inspected and electrically tested before energisation.

The theoretical load at the stated maximum ratings is approximately 3,250W, calculated as 13A multiplied by 250V. This should not be treated as a recommendation to operate every appliance continuously at that level. The permissible load depends on the actual supply voltage, circuit arrangement, cable capacity, protective device, installation conditions, and appliance characteristics. A qualified electrician should verify the complete circuit design.

The socket may be used for compatible portable appliances whose voltage, plug configuration, and current demand are within the outlet and circuit ratings. Typical applications can include lamps, televisions, computers, chargers, and suitable small appliances. High-load equipment must be checked against its nameplate current, circuit design, protective device, cable size, and manufacturer instructions before connection.

Its 250V AC and 13A ratings are compatible with the nominal low-voltage supply commonly used in the UAE. However, universal socket outlets may be subject to project specifications and the requirements of the relevant local authority, consultant, or developer. UAE installations commonly use BS 1363 Type G socket systems, so the contractor should confirm acceptance of a universal outlet before procurement or installation.

Key specifications include a rated current of 13A, rated voltage of 250V AC, universal socket outlet configuration, 1-gang format, flush-mounted installation, and approximate dimensions of 35 x 86 x 86 mm. The socket includes secure terminals for fixed-wiring connections and a built-in switch that allows the connected supply to be controlled at the outlet.

The ABB Millenium AM29486-MO is a 1-gang, flush-mounted universal socket outlet with an integrated switch for local power control. It is rated at 13A and 250V AC, features a mocha brown finish, and is designed to coordinate with compatible ABB Millenium frames and accessories. Its concealed wiring arrangement makes it suitable for residential, commercial, hospitality, and selected fit-out applications.