ABB Millenium 15A Double Pole Single Switched Socket Stainless Steel AM20986-ST

Contractors should verify the model number AM20986-ST, 15A round-pin plug compatibility, 250V AC rating, double-pole switching requirement, 1-gang configuration, flush box compatibility and stainless steel finish. They should also confirm circuit design, accessory schedule, frame selection and approval by the project consultant or relevant UAE electrical authority before procurement and installation.

Isolate the circuit before inspection or maintenance. Clean the visible surface with a soft, dry or slightly damp cloth, and avoid abrasive pads, aggressive chemicals or excessive moisture that could damage the finish or enter the mechanism. If there is overheating, discoloration, arcing, looseness or intermittent operation, stop using the outlet and have it inspected by a qualified electrician.

The installer should verify terminal tightness, conductor identification, protective-earth continuity, polarity, insulation resistance, circuit protection and secure mechanical fixing. The double-pole switch and socket should then be tested for correct operation. Testing and commissioning must be completed by a qualified professional using the approved project procedure and applicable UAE authority requirements.

Flush mounting conceals the back box, terminals and fixed wiring behind the finished wall, producing a neat installation suitable for premium residential and commercial interiors. It also coordinates well with blockwork, gypsum partitions and joinery when box positions and depths are planned before final finishes. The matching ABB Millenium frame helps maintain a consistent appearance across the project.

It may be used only where the equipment's normal operating current, starting current and plug type are compatible with the socket's 15A, 250V AC rating. High-load appliances, motors and equipment with significant inrush current require an engineering check. Loads exceeding the rating should use an appropriately designed dedicated connection, isolator or industrial socket.

The stainless steel finish provides a durable, contemporary appearance, but the supplied data does not state an IP rating. It should therefore not be assumed to be weatherproof or suitable for direct exposure to water, dust or outdoor conditions. Installation in kitchens, bathrooms, balconies or external areas requires confirmation of the required IP protection, zoning rules and local electrical regulations.

Cable size and protective-device rating must be determined by a qualified electrical engineer or electrician based on design current, installation method, cable length, voltage drop, ambient temperature, grouping and fault protection requirements. The socket must not be connected to a circuit that exceeds its 15A and 250V AC ratings. UAE authority requirements and the approved project electrical drawings should take precedence.

The socket face is approximately 86 x 86 mm and the overall stated depth is approximately 35 mm. The selected concealed box must be compatible with the ABB Millenium mechanism, fixing arrangement, cable entries and terminal clearance. Contractors should verify the exact back-box depth and frame compatibility before completing blockwork, drywall or wall-finishing activities.

The unit is installed flush into a compatible concealed wall box, with the permanent wiring terminated at the marked terminals according to ABB instructions. The circuit must be isolated and verified as de-energised before installation. After connecting live, neutral and protective earth as specified, the electrician should secure the socket, fit the matching frame and complete continuity, polarity, insulation and operational tests.

Yes, it can be specified for UAE villas, apartments, hotels, offices, retail spaces and other projects that require a 15A round-pin switched outlet. Its suitability depends on the approved electrical design, connected equipment and applicable authority requirements. A qualified electrician should confirm compliance with the relevant UAE electrical regulations and project specifications.

The outlet is intended for a compatible 15A round-pin plug operating within the socket's 250V AC and 15A ratings. It is not a standard UAE Type G rectangular-pin socket, so plug compatibility must be checked before purchase. The appliance load, cable size, circuit protection and plug configuration must all match the project design.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete circuit isolation than a single-pole switch, subject to correct wiring and installation. It is useful for compatible fixed electrical loads where convenient local isolation is required.

This ABB Millenium switched socket has a rated current of 15A, a rated voltage of 250V AC, a 15A round-pin outlet configuration and double-pole switching. It is designed for flush mounting and measures approximately 35 x 86 x 86 mm. The product includes secure terminals for fixed-wiring connections and has a stainless steel finish.

The ABB Millenium AM20986-ST is a 1-gang, flush-mounted 15A round-pin socket outlet with an integrated double-pole switch and stainless steel finish. Rated at 250V AC, it provides local power control while switching both the live and neutral conductors for more complete isolation of a compatible connected load.