ABB Millenium 15A Double Pole Single Switched Socket White Glass AM20986-WG

A qualified electrician should perform the tests required by the approved installation procedure, including protective-conductor continuity, insulation resistance, polarity, earth-fault protection and operation of the double-pole switch. RCD operation and circuit protective-device coordination should also be checked where applicable. The socket should only be energised after the circuit passes inspection and testing.

The supplied data does not state an ingress-protection or weatherproof rating, so it should not be assumed suitable for exposed outdoor, wet or dusty locations. Bathrooms, external walls, plant areas and similar zones may require an appropriately IP-rated accessory, suitable enclosure and specific placement. The installer must follow applicable zone restrictions and UAE project requirements.

The white glass face provides a clean, premium appearance suited to modern villas, apartments, hotels, offices and retail interiors in the UAE. Flush mounting keeps permanent wiring concealed and supports a neat wall finish. Confirm visual compatibility with other ABB Millenium accessories and protect the glass surface from impact, cement, grout, paint and abrasive cleaning products during construction.

That depends on the connected load and the project's electrical design. A dedicated radial circuit may be required for certain appliances or controlled loads. Circuit conductors, earthing, overcurrent protection and residual-current protection must be selected through a proper load assessment rather than from the 15A socket rating alone. Follow the approved drawings and the requirements of the relevant UAE electricity authority.

Contractors should verify the model number AM20986-WG, 15A and 250V AC ratings, round-pin connector format, double-pole operation, 1-gang configuration, flush-mounting requirement, dimensions and white glass finish. They should also confirm plug compatibility, approved back-box and frame arrangements, circuit schedules, load calculations, cable and breaker selection, earthing, RCD requirements and consultant or authority approvals.

The unit is designed for flush installation, with the wiring and mounting box concealed behind the finished wall. Installation should be completed with the circuit safely isolated and verified dead. A licensed electrician should confirm the back-box compatibility and depth, prepare the conductors correctly, connect live, neutral and earth to the identified terminals, tighten them to ABB's specified torque, secure the mechanism and frame, and complete electrical safety testing before energising.

Only if the appliance load does not exceed the socket's 15A rating and the equipment manufacturer and project design permit connection through a compatible 15A round-pin plug. Many air conditioners, water heaters, cookers and other fixed high-load appliances require a dedicated connection unit or isolator instead of a socket. A qualified electrician should calculate the design current and verify cable size, protective device, isolation and local authority requirements.

It can be used in suitable indoor residential, hotel, office, retail and commercial installations where a dedicated 15A round-pin connection is specified. Typical applications may include selected appliances or controlled circuits fitted with a compatible plug. The connected equipment's voltage, load current, plug type and manufacturer requirements must all match the outlet.

Its 250V AC rating is suitable for electrical systems operating within that rating, including the UAE's commonly used 230V, 50Hz supply. However, the 15A round-pin outlet must match the appliance plug and the approved project specification. The electrical consultant or licensed electrician should confirm compliance with the applicable UAE authority requirements, wiring regulations and approved socket standard before installation.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than a single-pole switch. It does not replace the circuit breaker, residual-current protection or an approved lockable isolator where these are required by the electrical design or local regulations.

The socket has a rated current of 15A, a rated voltage of 250V AC, a 15A round-pin outlet and a double-pole switching mechanism. It is a 1-gang flush-mounted unit measuring approximately 35 x 86 x 86 mm. Secure terminals support dependable fixed-wiring connections when the product is installed and tightened correctly.

The ABB Millenium AM20986-WG is a 1-gang, flush-mounted 15A round-pin socket outlet with an integrated double-pole switch and white glass finish. Rated at 250V AC, it switches both live and neutral conductors together and is designed for compatible fixed-wiring applications in residential, commercial and hospitality projects.

A qualified electrician should perform the tests required by the approved installation procedure, including protective-conductor continuity, insulation resistance, polarity, earth-fault protection and operation of the double-pole switch. RCD operation and circuit protective-device coordination should also be checked where applicable. The socket should only be energised after the circuit passes inspection and testing.

The supplied data does not state an ingress-protection or weatherproof rating, so it should not be assumed suitable for exposed outdoor, wet or dusty locations. Bathrooms, external walls, plant areas and similar zones may require an appropriately IP-rated accessory, suitable enclosure and specific placement. The installer must follow applicable zone restrictions and UAE project requirements.