ABB Millenium 45A Cooker Control Unit with 13A Switched Socket White Glass AM118147-WG

The supplied information does not state an IP rating, so it should not be assumed suitable for outdoor, exposed or wet-area installation. For locations subject to water, condensation, dust or harsh conditions, consult ABB documentation and select an enclosure or accessory with an appropriate verified environmental rating.

This model combines a 45A cooker control switch, a BS 13A switched socket, concealed installation and a coordinated white glass finish in one 2-gang unit. It is well suited to contemporary UAE kitchens where dependable fixed-wiring termination, accessible local control and coordination with ABB Millenium wiring accessories are important specification considerations.

The mounting surface should be flat, stable and properly finished so that the glass fascia is not stressed or unevenly supported. Allow sufficient box depth for the conductors without tight bends or trapped insulation. During tiling and painting, protect the mechanism from adhesive, grout, dust and moisture, and fit the decorative face only after wet trades are complete.

It may be suitable as a replacement when the existing circuit rating, mounting box, wiring condition, dimensions, frame system and switching configuration are compatible. The supply must be safely isolated, and the existing conductors and protective device must be inspected. Do not assume that every 45A cooker switch has the same box depth, terminals or pole arrangement.

The electrician should inspect terminal tightness and conductor identification, then complete the tests required by the approved installation procedure. These may include protective-conductor continuity, insulation resistance, polarity, earthing verification, protective-device operation and functional switching. The circuit should be energized only after satisfactory results are recorded.

Yes. Its flush-mounted configuration is suitable for concealed fixed wiring in villas, apartments, hospitality projects and kitchen fit-outs. Contractors should coordinate the mounting box, conduit entry, cable bend radius, wall finish and ABB Millenium frame before plastering, tiling or installing decorative cladding.

It should be installed in an accessible location where the cooker circuit can be operated without reaching across a hot cooking surface. Positioning must account for the appliance manufacturer's instructions, local electrical rules, kitchen layout, heat, steam, water sources and combustible finishes. The final location should be approved by the project consultant or qualified electrician.

The integrated cooker control switch provides convenient local control of the specified cooker circuit. Whether it satisfies the isolation requirements of a particular installation depends on its pole configuration, circuit design and applicable regulations. The product data lists the pole attribute as 1643 without defining it, so the exact switching arrangement should be confirmed from ABB documentation before specification.

The listed product dimensions are 42 x 147 x 86 mm, with a stated width of 147 mm. Before construction or fit-out work begins, verify the required wall-box size, recess depth, fixing centres and compatibility with the selected ABB Millenium frame, especially where tiles, stone cladding or kitchen splashbacks affect the finished wall depth.

Cable size cannot be specified from the 45A switch rating alone. It must be calculated using the cooker load, circuit length, voltage drop, ambient temperature, grouping, insulation, containment and installation method. UAE projects may also have authority- or consultant-specific requirements. The electrician must select conductors and protective devices that comply with the approved electrical design.

This model is designed for flush mounting, with the fixed wiring and compatible mounting box concealed behind the finished wall. Installation generally involves isolating and proving the supply dead, confirming the box and frame compatibility, terminating the conductors in the identified terminals, tightening them to the manufacturer's specified torque, fitting the mechanism and frame, and testing the completed circuit. Installation must be performed by a qualified electrician.

The 13A switched socket is intended only for appliances fitted with a compatible BS plug and operating within the socket and circuit limits. A high-load electric cooker requiring a dedicated fixed connection should be supplied through the 45A cooker circuit, not through the 13A socket. Follow the appliance manufacturer's connection instructions.

The cooker switch has a documented rated current of 45A. The actual connected cooker load must be determined from the appliance nameplate, supply voltage, diversity calculation, cable capacity, installation method and protective-device rating. A qualified electrical engineer or licensed electrician should verify that the complete circuit is correctly coordinated rather than selecting components by switch rating alone.

Yes. The unit is rated at 250V AC and incorporates a BS-style 13A switched socket, making it relevant to typical UAE residential and commercial kitchen installations. Circuit design, cable sizing, protective devices, earthing and installation must comply with the applicable UAE authority regulations, project specifications and local electrical requirements.