ABB Millenium 5A Double Pole Single Switched Socket Dune Sand AM22186-DU

The socket has a rated current of 5A and a rated voltage of 250V AC. It uses a 5A round-pin outlet configuration, incorporates double-pole switching, and is intended for flush mounting. Its stated dimensions are approximately 35 x 86 x 86 mm, making it suitable for compatible concealed wall-box installations.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than a single-pole switch, subject to correct wiring. The switch is not a substitute for isolating and locking out the circuit at the distribution board before electrical work.

Its 250V AC rating is compatible with the UAE's nominal 230V, 50Hz low-voltage supply, provided the connected appliance, round-pin plug, circuit protection, wiring and installation method are also suitable. Installation must comply with applicable UAE electrical regulations, project specifications and the requirements of the relevant local authority.

It is intended for compatible low-current equipment fitted with the correct 5A round-pin plug. Typical project applications may include selected lighting circuits, lamps or designated low-load equipment. The connected load must not exceed the 5A rating, and motor, heating or high-inrush loads should be assessed by a qualified electrical professional before connection.

No. A 5A round-pin socket has a different pin arrangement and a lower current rating than the BS 1363-style 13A socket commonly used in the UAE. It should only be used where the electrical design specifically calls for a compatible 5A round-pin outlet. Plug adaptors should not be used to bypass the socket's intended rating or circuit design.

The unit is designed for flush installation, with the fixed wiring and compatible mounting box concealed behind the finished wall. The installer should isolate the supply, verify the wall-box depth and accessory compatibility, terminate the conductors at the identified terminals, secure the mechanism without trapping cables, fit the matching frame or cover, and complete electrical testing before energising the circuit.

Installation should be completed by a licensed or suitably qualified electrician familiar with UAE wiring requirements and the relevant utility or authority regulations. The electrician should verify conductor size, earthing, polarity, protective-device rating, circuit identification and terminal tightness, followed by the required continuity, insulation and functional tests.

Contractors should confirm the 5A load requirement, round-pin plug compatibility, 250V AC rating, one-gang layout, double-pole switching requirement, compatible back-box depth, cable capacity and matching ABB Millenium frame or accessories. The Dune Sand finish should also be checked against the approved interior schedule, consultant submittal and project sample.

It can be incorporated into concrete, masonry or drywall construction when a compatible flush box and the correct installation method are used. For concrete or block walls, the box should be positioned before final plastering and kept level with the finished surface. For drywall partitions, use an approved cavity box and ensure the board can securely support the accessory.

The supplied information does not state an IP protection rating. It should therefore not be assumed suitable for exposed outdoor, wet, dusty or wash-down locations. Such environments require an appropriately rated weatherproof enclosure or accessory selected according to the site risk assessment and applicable UAE electrical requirements.

A dedicated 5A round-pin outlet can help distinguish selected lighting or controlled low-current circuits from general-purpose 13A outlets. This is useful in villas, hotels, offices and fit-out projects where floor lamps or other designated equipment must be locally or centrally controlled. The final circuit arrangement must follow the approved electrical design.

Yes. Flush mounting conceals the permanent wiring and mounting box behind the wall surface, while the ABB Millenium design provides a neat finished appearance. The Dune Sand colour is suited to coordinated neutral-toned interiors, subject to matching it with the specified frame and other wiring accessories.

Keep the faceplate clean with a soft, dry or lightly damp cloth and avoid abrasive cleaners, solvents and excessive water. Periodically check for heat discoloration, cracking, loose mounting, switch irregularity or poor plug retention. If any defect is found, isolate the circuit and arrange inspection by a qualified electrician rather than continuing to use the outlet.

A construction material submittal should identify the manufacturer, ABB Millenium series, model AM22186-DU, 5A current rating, 250V AC voltage rating, 5A round-pin connector type, double-pole switched operation, one-gang flush-mounted configuration, approximate 35 x 86 x 86 mm dimensions and Dune Sand finish. Compatibility with the proposed box, frame, wiring system and approved project requirements should also be documented.