ABB Millenium 5A Double Pole Single Switched Socket Matt Gold AM22186-MG

The principal specifications are a 5A rated current, 250V AC rated voltage, 5A round-pin socket configuration, double-pole switching and flush-mounted installation. The product measures approximately 86 x 86 mm across the face, with a listed overall dimension of 35 x 86 x 86 mm. Model AM22186-MG is supplied in a matt gold finish.

Double-pole switching means that the socket's switch disconnects both the live and neutral conductors at the same time. This provides more comprehensive local isolation than single-pole switching. It does not replace circuit isolation at the distribution board before installation, inspection or maintenance.

This outlet is intended for a compatible 5A round-pin plug, commonly associated with BS 546-type low-current connections. It may be used for suitable lighting equipment and other loads specifically designed for this plug system. Standard UAE 13A rectangular-pin plugs will not fit, and plug adapters should not be used to connect loads that exceed the socket or circuit rating.

It can be used as a controlled outlet for compatible lamps and lighting equipment where the electrical design specifies a 5A round-pin connection. This arrangement is often selected in villas, hotels and serviced apartments for switched floor lamps or table lamps. The circuit design, protective device and connected load must be checked by a qualified electrical professional.

The socket is rated at a maximum current of 5A at up to 250V AC. A simple voltage-current calculation gives 1,250W at 250V for a purely resistive load, but this should not be treated as a universal appliance limit. Motor, transformer, LED-driver and other inductive or high-inrush loads require separate assessment, and the connected equipment must remain within the socket, circuit and protective-device ratings.

The unit is designed for flush installation, with the wiring and mounting box concealed behind the finished wall. Installation generally involves isolating and proving the circuit dead, confirming the correct back box and cable arrangement, terminating the conductors at the marked terminals, securing the mechanism, fitting the matching face components and completing electrical tests. Installation should be carried out by a qualified electrician in accordance with the manufacturer's instructions and applicable UAE requirements.

The faceplate is approximately 86 x 86 mm and the listed product depth is about 35 mm, but the required back-box depth depends on terminal clearance, cable size, conductor bending space and the ABB Millenium mounting arrangement. Confirm compatibility with the selected ABB frame and wall box before closing blockwork, drywall or joinery. A deeper box may be preferable where cable routing is restricted.

The socket locations, mounting heights, circuit routes and back-box requirements should be coordinated during the electrical first-fix stage. The mechanism and matt gold finishing components are normally protected and installed during final fix after painting, tiling or wall finishes are substantially complete. Early coordination helps avoid box-depth conflicts, misalignment and damage to decorative surfaces.

Its 250V AC rating is compatible with the nominal low-voltage supply commonly used in the UAE, subject to the approved project design and local authority requirements. Installation should comply with applicable UAE regulations and the requirements of the relevant utility or authority, such as DEWA, ADDC or the authority serving the project location. The consultant or contractor should also verify project approval, plug standard and circuit protection before procurement.

Do not assume that this decorative flush-mounted socket is weatherproof or suitable for wet locations unless the product documentation confirms the required IP rating. Bathroom and kitchen positioning must observe applicable electrical-zone, moisture and local authority requirements. For outdoor, exposed, dusty or wash-down locations, use a suitably rated weatherproof enclosure or a purpose-designed IP-rated socket.

The fixed wiring must follow the terminal configuration and ABB installation instructions, including protective-earth continuity wherever an earth terminal is provided or required by the system. The circuit must have correctly selected overcurrent protection, and additional RCD or RCBO protection may be required by the installation design and applicable UAE regulations. Final polarity, insulation resistance, continuity and functional tests should be documented before energisation.

It is not a direct functional substitute for a standard 13A socket because it has a 5A rating and a different round-pin interface. Replacement is appropriate only where the circuit and connected equipment are specifically designed for a 5A round-pin outlet. The electrician must also confirm back-box compatibility, wiring condition, circuit protection and compliance with the approved electrical design.

Keep the visible components in their protective packaging until final fix and avoid exposure to cement, grout, paint, silicone, solvents and abrasive tools. Clean the surface with a soft, dry or slightly damp cloth after isolating the supply, and do not use acidic, alkaline or abrasive cleaners. During construction, protect the socket from impact and dust without trapping moisture against the finish.

Verify the model number AM22186-MG, 5A round-pin plug requirement, 250V AC rating, double-pole switching, 1-gang layout, matt gold finish and flush-mounting dimensions. Contractors should also confirm the compatible ABB Millenium frame, back box, accessory schedule, circuit design and required quantity. Matching model and finish references across the project helps maintain consistency during procurement and final installation.