ABB Millenium 5A Double Pole Single Switched Socket White Glass AM22186-WG

Check the full ABB model number AM22186-WG, 1-gang configuration, 5A rated current, 250V AC rating, 5A round-pin connector, double-pole switched operation, flush-mounted format, 86 x 86 mm face dimensions and White Glass finish. These details should match the bill of quantities, approved material submittal, wiring drawings and adjacent ABB Millenium accessories.

Yes. Keep the visible face protected from cement slurry, paint, grout, dust and impact during construction. Install the decorative frame after heavy finishing work where the project sequence permits, use a soft non-abrasive cloth for cleaning and avoid harsh chemicals or abrasive pads. Do not overtighten fixings, as excessive force can damage the accessory or affect alignment.

A qualified electrician should perform the tests required by the applicable regulations and project inspection plan. These may include protective-conductor continuity, insulation resistance, polarity, correct double-pole switching, terminal security, earth-fault loop or protective-device verification and functional operation. Results should be recorded where commissioning documentation is required.

Circuit protection must be selected by the electrical designer according to the connected load, cable size, installation method, fault level and applicable regulations. The socket's 5A rating must not be exceeded. Required overcurrent protection, earthing and residual-current protection should be established through the approved circuit design rather than inferred from the outlet rating alone.

Do not assume suitability for wet, damp or outdoor locations because an IP rating is not stated in the supplied product information. For bathrooms, kitchens, balconies or external areas, the designer must assess water exposure, installation zones, enclosure protection, earthing and any required residual-current protection. Use a suitably rated weatherproof accessory where the location demands it.

Yes, it may be used in these common construction systems when a compatible flush box and the correct installation method are selected. Concrete and blockwork generally require a properly positioned concealed box and conduit, while gypsum partitions need a suitable dry-lining box or supported enclosure. The finished box must be level, adequately recessed and deep enough for safe cable termination.

Its 250V AC rating is compatible with the nominal low-voltage supply commonly used in the UAE, but suitability depends on the approved circuit design and intended load. Installation must comply with applicable UAE regulations, the relevant local authority requirements, project specifications and manufacturer instructions. Approval expectations can vary between authorities and developments, so the electrical consultant or licensed contractor should confirm compliance.

Contractors should verify the 5A load requirement, 250V AC supply compatibility, round-pin plug format, double-pole switching requirement, wall-box dimensions, mounting depth and White Glass finish. The item should also be checked against approved drawings, material submittals, room data sheets and the project's electrical specifications before procurement.

The unit is designed for flush mounting in a compatible concealed wall box. After safely isolating and verifying the circuit is dead, a qualified electrician should prepare the conductors, connect them to the identified terminals, confirm earth continuity where applicable, secure the mechanism without trapping cables and fit the matching frame. The completed circuit should then undergo the required inspection and electrical testing before energisation.

No. This model is a 5A round-pin socket and is not the same as the commonly used UAE Type G rectangular-pin outlet. A Type G plug should not be forced into the socket or connected through an unsuitable adapter. Use only a compatible 5A round-pin plug and follow the electrical consultant's socket schedule.

This outlet is intended for compatible equipment fitted with the correct 5A round-pin plug and operating within the socket's electrical rating. Typical project applications may include selected lighting circuits, controlled lamps or other specified low-current loads. The connected load must not exceed 5A, and the appliance voltage, plug type and circuit design must all be verified.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than a single-pole switch, subject to correct wiring and circuit design. It does not replace isolation at the distribution board before electrical installation or maintenance.

The socket is rated at 5A and 250V AC and uses a 5A round-pin outlet configuration. It features double-pole switching, secure fixed-wiring terminals and flush mounting. Its stated overall dimensions are 86 x 86 mm, with a listed depth of 35 mm; installers should confirm the required wall-box depth and fixing arrangement before installation.

The ABB Millenium AM22186-WG is a 1-gang, 5A round-pin socket outlet with double-pole switching and a White Glass finish. Designed for flush-mounted installations, it provides local control of a compatible low-current circuit while switching both the live and neutral conductors.