ABB Millenium Shaver Socket Outlet Stainless Steel AM40188-ST

Isolate the circuit before inspection or maintenance. Clean the visible surface with a soft, lightly damp cloth and dry it immediately; do not use abrasive pads, acidic cleaners, bleach or solvents that could damage the finish. Periodically check for looseness, discoloration, overheating, cracking or moisture exposure. Any internal inspection, repair or replacement must be performed by a qualified electrician.

Yes, subject to using the correct compatible back box and fixing method. For blockwork or tiled walls, the box must be positioned accurately before final plastering or tiling so the accessory sits flush without stressing the faceplate. For gypsum partitions, a suitable dry-lining box and adequate support are required. Contractors should coordinate box depth, conduit entry and finished wall thickness during first-fix electrical work.

Its concealed installation, coordinated ABB Millenium styling and stainless-steel appearance make it suitable for UAE villas, apartments, hotels and commercial washroom fit-outs where a clean architectural finish is required. The 230V AC rating aligns with common UAE low-voltage installations, but final compliance depends on correct circuit design, approved materials and installation in accordance with the local authority having jurisdiction, such as DEWA or the applicable emirate utility and project consultant requirements.

This product is identified as a shaver socket outlet and is intended for compatible shaver or grooming-appliance connections, not as a replacement for a standard UAE 13A socket outlet. Plug compatibility and permitted appliance ratings should be confirmed from the outlet markings and ABB product documentation. Never use adaptors or connect an appliance whose voltage, plug type or load is not approved for the socket.

No. Stainless steel describes the visible decorative finish and does not by itself confirm an IP rating, waterproof construction or suitability for wet or outdoor environments. The outlet should be installed indoors and protected from direct water spray, condensation and harsh cleaning chemicals. Confirm the product's documented IP classification and permitted bathroom location before specifying it for moisture-prone areas.

The electrician should check terminal tightness, conductor identification, polarity where applicable, continuity of protective conductors, insulation resistance and the operation of relevant protective devices. The accessory should also be checked for secure mounting, correct frame alignment and damage. Testing and commissioning must follow the manufacturer instructions, the project specification and the requirements of the relevant UAE authority.

The AM40188-ST requires a compatible concealed mounting box and ABB Millenium frame selected for the mechanism configuration and wall construction. Back-box depth and fixing arrangements should be checked before cutting blockwork, gypsum board, tile or joinery. Because the listed overall product dimensions may not represent the required wall opening, contractors should use the official ABB installation drawing to determine the exact cut-out and box size.

Installation begins by isolating and verifying the electrical supply, preparing a compatible concealed wall box, routing the approved fixed wiring and terminating the conductors according to the ABB wiring diagram. The mechanism is then secured in the wall box, aligned with the finished surface and completed using the appropriate ABB Millenium frame. The circuit must be electrically tested before energisation. Installation should only be completed by a licensed or suitably qualified electrical professional.

It may be used in a bathroom only when its location, circuit design and installation comply with applicable UAE electrical regulations and bathroom safety-zone requirements. A qualified electrician must confirm whether the proposed mounting position is permitted and whether additional protection, isolation or bonding is required. Do not install it close to showers, bathtubs or washbasins unless the location is specifically allowed by the relevant regulations and manufacturer instructions.

This outlet is intended for indoor locations where a dedicated connection for compatible electric shavers or similar manufacturer-approved grooming appliances is required. Typical applications include bathrooms, washrooms, hotel guest rooms, serviced apartments, villas and premium residential developments. It should not be treated as a general-purpose socket or used to supply high-load appliances.

The AM40188-ST has a rated voltage of 230V AC, a flush-mounted installation format and a shaver socket outlet connection. The listed overall dimensions are 42 x 95 x 190 mm, with a stated width of 95 mm. Contractors should verify the required wall box, installation depth, frame compatibility and circuit requirements against the ABB technical documentation before ordering or installation.

The ABB Millenium AM40188-ST is a 230V AC shaver socket outlet designed for permanent indoor fixed-wiring installations. It features flush mounting to conceal wiring, secure cable terminals and a stainless-steel finish that coordinates with compatible ABB Millenium frames and electrical accessories. It is suitable for professionally specified residential, hotel and commercial fit-out projects.

Isolate the circuit before inspection or maintenance. Clean the visible surface with a soft, lightly damp cloth and dry it immediately; do not use abrasive pads, acidic cleaners, bleach or solvents that could damage the finish. Periodically check for looseness, discoloration, overheating, cracking or moisture exposure. Any internal inspection, repair or replacement must be performed by a qualified electrician.

Yes, subject to using the correct compatible back box and fixing method. For blockwork or tiled walls, the box must be positioned accurately before final plastering or tiling so the accessory sits flush without stressing the faceplate. For gypsum partitions, a suitable dry-lining box and adequate support are required. Contractors should coordinate box depth, conduit entry and finished wall thickness during first-fix electrical work.