منفذ بيانات أحادي (RJ45) من (ABB) مع لوحة موديل (Inora BL331) لون أبيض

Confirm that SKU 42201-NOS matches the required ABB Inora range, white finish and single-gang layout. Also verify the compatible RJ45 module, cable category, back box, support or mounting accessories and required quantity. Because this item is supplied as a plate only, these additional components may need to be purchased separately.

Isolate connected equipment where appropriate and wipe the plate with a soft, dry or slightly damp cloth. Do not use abrasive pads, solvents or strong chemical cleaners, as these may damage or discolor the finish. Keep liquids and dust away from the RJ45 connector, and inspect loose or damaged outlets during routine building maintenance.

It is primarily intended for indoor use and no outdoor IP rating is stated in the supplied product information. For balconies, plant areas, external walls or other locations exposed to water, dust, heat or direct sunlight, use a weatherproof data enclosure with an appropriate IP rating and components approved for the site conditions.

It can provide the faceplate for a compatible RJ45 module used with IP phones or structured voice networks. Suitability for analogue telephone services depends on the selected module, cabling layout and connector assignment. The plate itself does not determine the communication protocol or network performance.

Yes, it is suitable for indoor structured-cabling outlets in residential and commercial UAE projects when installed with compatible components. Selection and installation should comply with the approved project drawings, local authority requirements and relevant standards such as ISO/IEC 11801 or ANSI/TIA structured-cabling guidance where specified. Environmental suitability must also be considered for hot, humid or dusty locations.

After termination, check wire mapping, continuity, pair sequence and labeling with an appropriate network cable tester. For projects requiring certified performance, use a calibrated field certifier suitable for the installed cable category and test the permanent link against the applicable project standard. Record test results for commissioning and handover documentation.

Contractors should verify the outlet location, finished-wall depth, back-box alignment, conduit capacity, cable category, bend radius and coordination with furniture and electrical services. Data cable should be protected from plaster, paint, moisture and physical damage. The faceplate should be fitted after dusty finishing activities are complete to preserve its white surface and connector area.

Separating data and power cabling helps reduce electromagnetic interference and supports stable Ethernet performance. UAE construction projects commonly route structured cabling through dedicated conduits, trunking compartments or containment systems. Required separation and crossing methods should follow the project specification, the relevant authority requirements and recognized structured-cabling practices.

The BL331 is a single-gang plate, but wall-box dimensions and fixing arrangements can vary between projects. Confirm compatibility with the specified ABB Inora mounting system, back box, support frame and RJ45 module before installation. This is especially important for renovation work where existing boxes may belong to another accessory range.

Install a suitable back box at the planned outlet position, route the approved data cable with adequate separation from power wiring, terminate the cable onto the compatible RJ45 module using the specified T568A or T568B scheme, secure the module in the plate and fix the assembly level to the box. Maintain cable bend radius and avoid excessive untwisting of pairs. The finished link should be labelled and tested before handover.

It is suitable for indoor data points in UAE villas, apartments, offices, retail spaces, hotels, schools and other commercial projects. Typical applications include wired connections for computers, smart TVs, printers, IP phones, wireless access points and other Ethernet-enabled devices. Installation in damp, dusty or outdoor areas requires an enclosure specifically rated for those environmental conditions.

Cable performance is determined by the separately selected RJ45 module, patch panel and structured cabling rather than by the faceplate itself. Depending on the compatible module, the outlet may form part of a Cat5e, Cat6 or Cat6A installation. For reliable performance, every permanent-link component should meet the same category and be installed and tested accordingly.

It's a single-gang wall plate with an integrated RJ45 data outlet. 'Plate only' means this listing provides the front plate with the RJ45 module built in; there are no additional modules to install beyond the plate itself.

The ABB Inora BL331 is a single-gang faceplate designed to provide a neat wall outlet for an RJ45 network connection in homes, offices and commercial buildings. Its modern white finish suits contemporary interiors and coordinated ABB Inora wiring accessories. This listing is for the plate only, so the compatible RJ45 data module, cable, back box and installation accessories should be confirmed separately.