مقبس كهربائي مرن أحادي (20Amp) من (ABB) موديل (Inora BL120) لون أبيض

Check the product reference BL120, SKU 42198-NOS, 20A rating, white colour and listed dimensions of 24.2 x 86 x 86 mm against the project schedule and back-box requirements. The listed EAN is 6941593436507. For construction orders, confirm the required quantity, appliance loads, circuit arrangement and consultant-approved material submittal before purchasing.

Keep the faceplate clean and dry, using a soft cloth without abrasive cleaners or aggressive solvents. Periodically check for discoloration, cracking, looseness, unusual heat or a burning smell. If any defect is found, isolate the circuit and have the accessory inspected by a qualified electrician. Electrical terminals should never be accessed while the circuit is energised.

The electrician should carry out the tests required by the project specification and applicable wiring regulations. These can include protective-conductor continuity, insulation resistance, polarity, earth-fault loop impedance and RCD operation where relevant. Terminal security, cable restraint, faceplate alignment and functional operation of the connected equipment should also be checked before handover.

Its single-gang format supports tidy cable termination at finished wall level, helping contractors achieve an organised appearance in residential and commercial interiors. The white finish works with many common décor schemes, while the 86 x 86 mm faceplate format is practical for coordinated electrical layouts. Back-box compatibility and approved accessory schedules should still be checked before bulk installation.

Not unless it is housed within a suitably rated weatherproof enclosure and approved for the intended location. UAE outdoor installations can be exposed to dust, moisture, heat and strong sunlight. Because no standalone IP or UV-resistance rating is specified in the available product data, the BL120 is best treated as an indoor accessory unless the project consultant approves an appropriate protective installation.

It can be considered only when its location and installation comply with the applicable requirements for wet areas. Bathrooms, kitchens and utility rooms may require specific zones, clearances, RCD protection and suitable ingress protection. The supplied product information does not state an IP rating, so it should not be assumed to be weatherproof or suitable for direct exposure to water.

It may be used as part of a correctly designed connection for compatible equipment, but suitability must be verified from the appliance nameplate, starting current, manufacturer’s instructions and circuit design. High-load equipment such as water heaters and air-conditioning units may require dedicated circuits, double-pole isolation or other protective devices. Approval by the project electrician or electrical engineer is recommended.

That depends on the connected appliance and circuit design. A flex outlet mainly provides a cable exit and termination point; it should not automatically be treated as a local isolator or fused connection unit. If local isolation, switching or additional overcurrent protection is required, the appropriate device must be installed in accordance with the equipment instructions and approved electrical drawings.

Cable size cannot be selected from the outlet rating alone. It must be calculated according to connected load, circuit length, installation method, ambient temperature, grouping, voltage drop and protective-device rating. UAE projects commonly follow approved specifications based on BS 7671 or relevant IEC principles, together with local authority rules. A qualified electrical engineer or electrician should confirm the conductor size.

Installation should be completed by a qualified electrician. The circuit must first be isolated, locked out where required and tested to confirm it is dead. The electrician should prepare the back box, route the correct cable, make secure terminal connections according to the product markings, fit any required cable restraint, install the faceplate level with the finished wall and then perform the prescribed electrical tests before energising the circuit.

The listed dimensions are 24.2 x 86 x 86 mm. Contractors should verify the compatible back box, available wiring depth, cable entry position and wall finish before installation, particularly when working with tiled surfaces, gypsum partitions, blockwork or prefabricated wall systems.

Yes, its 20A capacity, white finish and common 86 x 86 mm format make it relevant to villas, apartments, offices, shops and other UAE fit-out projects. Before specification, the contractor should confirm compliance with the approved project drawings, local authority requirements and applicable electrical regulations, which may include DEWA, ADDC, SEWA or the relevant emirate’s authority requirements.

A 1 gang flex outlet provides a finished wall connection through which a flexible cable can be routed to fixed equipment. Typical applications can include suitable water heaters, extractor fans, air-conditioning accessories, kitchen equipment, lighting equipment and other permanently positioned appliances. Compatibility depends on the equipment load and the project’s electrical design.

It’s a 1-gang, combined switch and outlet designed for indoor use. The BL120 model provides a 20 Amp rated outlet within a sleek white finish, offering a convenient, compact way to power devices while also enabling a built-in control switch in a single wall box.