ABB Inora 1 Gang 1 Way 20AX Switch Royal Gold BL110-PG

One gang means the switch has one control rocker. One way means it operates a circuit from a single location rather than from two or more switching points. The 20AX designation indicates a 20 A switch rating with suitability for loads that can produce higher switching currents, such as certain fluorescent or inductive lighting circuits. The connected load must still remain within the product marking and circuit design limits.

Yes, it can be used as a local control switch for a compatible lighting circuit in villas, apartments, offices, shops and hospitality interiors. The circuit voltage, load type, protective device, cable size and installation method must match the switch markings and the approved electrical design. Compliance with applicable UAE authority requirements and project specifications should be confirmed before installation.

It may be used to switch compatible LED lighting, provided the total steady-state current and the LED drivers' inrush current are within the switch manufacturer's permitted limits. Large groups of LED drivers can create high startup current even when their normal wattage is low. For substantial lighting banks, a suitably rated contactor or relay may be required.

Installation should be completed by a qualified electrician. The circuit must first be isolated, locked out where required and tested to confirm it is de-energised. The incoming live conductor and switched-live conductor are then connected to the terminals identified on the product, following ABB's wiring diagram. After secure termination, the mechanism is fitted into a compatible wall box, aligned, assembled with its cover and functionally tested.

A conventional mechanical one-way switch normally interrupts the live conductor and generally does not require a neutral connection at the switch mechanism. However, the exact terminal arrangement must be verified from the markings or installation instructions supplied with the BL110-PG. Neutral and protective-earth conductors must be managed according to the circuit design and local wiring requirements.

No. This model is specified as a one-way switch and is intended to control one circuit from one location. For corridors, staircases, bedrooms or other spaces requiring control from two positions, use compatible two-way switches. Intermediate switching components may also be needed when control is required from three or more locations.

Use a wall box, mounting arrangement, cover components and accessories compatible with the ABB Inora range and the project's installation system. Box depth should allow adequate space for conductors without tight bending or terminal stress. Confirm mounting centres, box dimensions and accessory compatibility before procurement, especially for concealed installations, modular systems and replacement work.

The Royal Gold finish is well suited to premium villas, hotel rooms, reception areas, offices and retail fit-outs where electrical accessories form part of the interior design. It can complement warm metallic hardware and decorative finishes. For a consistent appearance, coordinate the switch with compatible ABB Inora plates and accessories from the same finish range.

It should only be used where the connected load type and switching current comply with ABB's published rating. Motor loads can have startup currents significantly above their normal operating current, so the 20AX marking alone should not be treated as automatic approval for every fan, pump, motor or site appliance. Higher-load equipment may require a dedicated isolator, motor starter, relay or contactor selected by an electrical engineer.

Contractors should verify the product's marked voltage and current ratings, load characteristics, wiring diagram, wall-box compatibility, finish schedule and required quantities. Installation should follow the approved project drawings, relevant IEC or BS-based wiring practices where specified, and the regulations of the applicable UAE authority, such as DEWA, ADDC or the relevant local utility. Consultant approval and project-specific requirements take precedence.

Do not assume that this decorative indoor switch is weatherproof. Outdoor, bathroom or exposed installations require an enclosure and accessory system with an appropriate verified IP rating for moisture, dust and environmental exposure. Product documentation and local zone requirements must be checked before installation in kitchens, wash areas, balconies, gardens or external walls.

Isolate the electrical supply before inspection or maintenance. Clean the visible surface with a soft, dry or lightly damp cloth and avoid abrasive pads, harsh chemicals, solvents and excessive water, as these may damage the Royal Gold finish. A qualified electrician should investigate loose operation, overheating, discoloration, arcing sounds or intermittent switching.

This ABB Inora switch combines straightforward one-location circuit control, a 20AX switching designation and a decorative Royal Gold appearance. Model BL110-PG is suitable for buyers searching for an ABB gold wall switch for villas, apartments, offices, hotels and retail fit-outs, subject to correct load selection, compatible accessories and professional installation.