ABB Inora 1 Gang Data Outlet Housing Royal Gold BL331-H-PG

This face plate should be used with a compatible ABB Inora data module or insert specified for the BL331-H-PG arrangement. Depending on the selected system, the outlet may be configured for applications such as RJ45 network, telephone or other extra-low-voltage communication connections. Compatibility should be checked against the module series, mounting mechanism and back-box depth before ordering, as similarly sized modules from other ranges may not fit correctly.

A 1 gang face plate is intended for one standard outlet position or one compatible accessory assembly. It is commonly installed at an individual data point beside a workstation, television location, Wi-Fi access point, reception desk or building-management interface. The term does not necessarily indicate the number of data ports, because the final port configuration depends on the compatible insert or module installed.

The ABB Inora Royal Gold face plate is suitable for indoor data outlet installations in villas, apartments, offices, hotels, retail units and other finished construction projects. It is particularly relevant where a decorative gold-coloured accessory is required to coordinate with luxury interior finishes. For kitchens, washrooms, outdoor spaces or exposed service areas, the installer should assess moisture, dust and impact conditions and select an appropriately rated enclosure if necessary.

First install a compatible flush or surface back box at the specified location and route the approved data cable through suitable containment. Terminate the cable onto the compatible data module according to the module manufacturer's wiring scheme, secure the module in its support or mounting frame, and then fit the face plate evenly without overtightening. The outlet should be labelled and tested after installation. Installation should be completed by a qualified ELV or structured-cabling technician in accordance with the project drawings and local requirements.

The required back box must match the ABB Inora mounting system and provide enough internal depth for the selected data module, cable bend radius and termination hardware. Data cables should not be sharply bent or compressed behind the outlet, as this can reduce network performance. Because the product information does not specify the back-box dimensions or depth, these details should be verified using the ABB technical documentation and the requirements of the selected module before wall preparation begins.

It may be positioned near power accessories when the design requires a combined workstation or media outlet, but power and data cabling must be suitably separated. Use dedicated containment, dividers or separate back boxes where required, and avoid routing data cables parallel to power cables for long distances. Proper segregation helps reduce electromagnetic interference and supports safe installation in accordance with applicable UAE electrical regulations, project specifications and structured-cabling practices.

Yes, it is relevant to UAE residential, commercial and hospitality projects that require a decorative single-gang data outlet with a Royal Gold finish. Before specification, the consultant or contractor should confirm compatibility with the project's structured-cabling system, approved back boxes, fire-rated wall requirements and authority guidelines. Installation should follow the applicable requirements of the relevant UAE authority, such as DEWA, ADDC or the local municipality, together with approved project drawings and manufacturer instructions.

Contractors should confirm outlet locations, mounting heights and quantities from the approved ELV and interior-design drawings before first-fix work. The correct back boxes and conduits should be installed before plastering or drywall closure, with sufficient cable allowance for termination. During second fix, protect the Royal Gold surface from paint, grout, adhesive and tools. Each completed data point should be labelled and tested, and its identification should correspond with the patch-panel schedule and as-built documentation.

Isolate nearby electrical accessories where appropriate, then wipe the face plate with a soft, dry or slightly damp microfibre cloth. Do not use abrasive pads, metal polish, thinners, bleach or strong chemical cleaners, as they may scratch or discolour the decorative finish. Ensure moisture does not enter the data module or back box. During construction, keep the plate covered until final cleaning and handover to prevent damage from dust, paint and cement-based materials.

The product is identified as a data face plate, so buyers should not assume that an RJ45 module, network cable, back box, mounting support or termination accessories are included unless they are specifically listed in the supplied package. These components are normally selected according to the required network category and project specification. Confirm the package contents and compatible ABB Inora accessories before purchase.

Use network cable, keystone or data modules, patch panels and patch cords of the category specified for the project, and maintain the manufacturer's permitted bend radius and untwisting limits during termination. Keep data cabling separated from power circuits and sources of electrical interference. After installation, test each link using suitable structured-cabling test equipment and record the results for commissioning and handover. The face plate provides the finished outlet interface but does not determine network speed by itself.