ABB Inora 1 Gang Data Outlet Housing White BL331-H

It can be used for data outlet points in villas, apartments, offices, retail units, hotels, schools and other structured-cabling installations. Typical applications include wall outlets for network, internet, telephone or compatible low-voltage communication modules, subject to the selected insert and project design.

The product name identifies it as a data face plate and does not confirm that an RJ45 module or data jack is included. Buyers should check the supplied contents and select a compatible ABB Inora data module separately if required. The module category, such as Cat6 or another rating, must match the network cable and project specification.

Install the compatible data module and terminate the cable according to the module manufacturer's wiring instructions. Secure the support assembly to a suitable one-gang flush or surface back box, arrange the cable without sharp bends or excessive tension, and fit the face plate squarely over the assembly. Installation should be completed by a qualified ELV or structured-cabling technician, particularly on commercial construction projects.

Use a one-gang back box that is mechanically compatible with the ABB Inora system, fixing centres and installation depth. The box must also provide enough space for the data module, cable bend radius and termination hardware. Before ordering for a UAE project, verify the wall-box dimensions against the ABB product documentation, approved material submittal and site sample.

Yes, it may be used on drywall or masonry walls when paired with the correct compatible back box and fixing method. Drywall installations normally require a suitable hollow-wall box, while blockwork or concrete walls generally use a flush box positioned during civil or MEP works. The finished box should be level, securely fixed and aligned with the final wall surface.

The face plate itself is a passive mounting and finishing component, so the network category depends on the installed data jack, cable, patch panel and termination quality. For a Cat6 installation, use a compatible Cat6-rated module and cable, maintain the specified bend radius and pair twist, and test the completed link using appropriate certification equipment.

It is relevant for UAE villas, apartments, offices and fit-out projects requiring a clean, professional data outlet finish. Suitability should be confirmed against the consultant's approved material schedule, project ELV specification, local authority requirements and the compatibility of the selected ABB Inora components. For large developments, a sample installation and material approval are recommended before bulk procurement.

Data and power cabling should normally be segregated to reduce electrical interference and support safe, compliant installation. Use separate conduits, containment or suitably partitioned systems as required by the project specification and applicable UAE electrical and ELV practices. Do not place communication terminations in an unpartitioned box with mains wiring unless the complete system is specifically designed and approved for that arrangement.

Confirm the model number BL331-H, white finish, one-gang configuration, compatible back box, required data module and the number of outlet points shown on the approved drawings. Contractors should also verify whether modules and supports are included, review the consultant's material approval requirements, and coordinate quantities with architectural and ELV schedules to avoid mismatched accessories on site.

Provide sufficient cable length for termination without leaving excessive coils inside the back box. Avoid kinks, crushing and tight bends, and keep the cable away from power wiring and sources of electromagnetic interference. Maintain the cable manufacturer's bend-radius and pulling-tension limits, preserve pair twists close to the termination point, and label both ends according to the project's structured-cabling schedule.

After termination, perform continuity and wire-map testing at minimum. For specified network performance, use a calibrated cable certification tester suitable for the installed category and permanent-link standard. Record outlet identification and test results for inclusion in the project's ELV testing and commissioning documentation.

This face plate should not be assumed to be weatherproof or suitable for exposed outdoor areas unless an appropriate ingress-protection rating is confirmed in official ABB documentation. For balconies, gardens, service yards or other locations exposed to dust, heat, humidity or water, install the outlet within a compatible weatherproof enclosure selected for the environmental conditions.

Disconnect or protect nearby equipment before cleaning, then wipe the surface with a soft, dry or lightly damp cloth. Do not use abrasive pads, solvents or aggressive chemicals, as they may damage or discolour the finish. Periodically check that the plate is secure and inspect the data outlet if connectivity becomes intermittent.

The ABB Inora BL331-H provides a tidy, coordinated wall finish for a single compatible data point and is suited to modern residential and commercial interiors. Its one-gang format supports straightforward outlet planning, while the white finish can integrate with common wall colours and matching ABB Inora wiring accessories. Final performance depends on using the correct module, cable and professional termination practices.