ABB Inora 1 Gang 45-Degree Satellite F-Type Outlet Royal Gold BL308-PG

This socket is typically used to connect a satellite receiver, television system or compatible set-top box to a building's coaxial satellite distribution network. Common applications include UAE villas, apartments, hotels, offices and mixed-use developments with concealed low-voltage or extra-low-voltage communication cabling.

The satellite connection is angled at approximately 45 degrees rather than projecting straight out from the wall. This arrangement can improve cable routing, reduce sharp bending near the connector and create a tidier installation behind televisions, media cabinets and wall-mounted entertainment systems.

It is a satellite signal outlet for coaxial communication cabling, not a mains power outlet. It does not supply 230 V power to televisions or receivers. A separate, correctly rated electrical socket must be installed where equipment requires mains electricity.

Yes, it is suitable for indoor satellite TV outlet installations in UAE residential and commercial projects when it matches the specified ABB Inora wiring-accessory system, back box, coaxial cable and network design. Final selection and installation should follow the project's approved drawings, consultant requirements, manufacturer instructions and applicable UAE authority regulations.

Installation normally involves preparing the compatible wall box, routing the approved coaxial cable without tight bends, terminating the cable using the correct connector method, securing the SAT outlet mechanism and fitting the Royal Gold front plate. The cable should then be tested for continuity, signal quality and secure termination. Installation should be completed by a qualified electrician or ELV technician in accordance with ABB instructions and project specifications.

Use a back box that is compatible with the ABB Inora 1-gang mechanism and provides sufficient depth for the terminated coaxial cable. Adequate depth is important because satellite cable should not be crushed or sharply bent behind the outlet. Confirm mounting dimensions and box compatibility against the current ABB product documentation before installation.

Use a quality 75-ohm coaxial cable specified for satellite-frequency signal distribution, together with compatible connectors and splitters. For UAE construction projects, cable type should follow the approved ELV or SMATV design, fire-performance requirements and consultant specifications. Cable runs should be kept away from sources of electrical interference and protected from crushing or excessive bending.

It may be used as an endpoint in a compatible satellite master antenna television or SMATV network, subject to the system designer's specifications. The outlet, cable, splitters, multiswitches and amplifiers must support the required frequency range, impedance and signal levels. Compatibility should be verified by the ELV contractor before procurement or installation.

It can be included in a coordinated media and power outlet arrangement where the selected ABB system and project design permit it. Mains and communication cables must remain correctly segregated, and suitable boxes or barriers should be used where required. Follow ABB installation guidance, approved construction drawings and applicable UAE electrical and building requirements.

The Royal Gold finish is intended mainly for indoor decorative applications such as living rooms, bedrooms, hotel rooms and executive offices. It should be protected from abrasive cleaners, construction chemicals and scratching. For outdoor, wet, dusty or high-humidity locations, use an accessory and enclosure with an explicitly suitable ingress-protection rating; no such rating should be assumed for this indoor decorative socket.

Isolate nearby electrical circuits where necessary, then wipe the faceplate gently with a soft, dry or slightly damp cloth. Do not use solvents, abrasive pads or strong chemicals, as they may damage the Royal Gold surface. If satellite reception deteriorates, an ELV technician should inspect the connector, cable termination and system signal levels rather than repeatedly moving or forcing the plug.

Use approved 75-ohm coaxial cable, make clean and secure terminations, avoid unnecessary joints and prevent tight cable bends. Keep the coaxial route suitably separated from mains wiring and interference sources. After installation, test the outlet with appropriate signal-measuring equipment to confirm that the delivered level and quality meet the satellite or SMATV system design.

Contractors should verify model number BL308-PG, Royal Gold colour, 1-gang format, SAT connector compatibility, back-box dimensions, plate or frame requirements and the approved ABB Inora range specified for the project. They should also confirm the quantity required from the outlet schedule and ensure that all related coaxial network components are technically compatible.

Yes, it can be used in renovations where the existing box, mounting arrangement and coaxial network are compatible. Before replacement, inspect the cable condition, available box depth and connector type. Older satellite networks may also require signal testing or component upgrades, so the outlet should not be assumed to resolve reception problems caused elsewhere in the system.