ABB Inora 1 Gang 13A Double Pole Switched Socket Outlet White BL237

DP means double pole. When the socket switch is turned off, it disconnects both the live and neutral conductors. This feature is useful in UAE electrical installations because it provides enhanced isolation for connected equipment, particularly during cleaning, servicing or periods when an appliance is not being used.

The BL237 is designed for 13A socket applications commonly used with the UAE's nominal 230V, 50Hz electrical supply. Project consultants and contractors should verify the socket specification against the approved electrical drawings, applicable BS 1363 requirements and the regulations of the relevant UAE authority, such as DEWA, ADDC or another local utility. Final suitability depends on the complete circuit design and project approval.

It can be used for compatible plug-in equipment with a current demand within the socket and circuit rating, including computers, televisions, chargers, small kitchen appliances and general office equipment. High-load appliances must be checked using their nameplate wattage and current. Equipment that requires a dedicated circuit, fused connection unit or isolator should not be connected merely because it has a compatible plug.

Yes. The socket is suitable for common indoor fit-out requirements in villas, apartments, offices, retail spaces, hotels and other commercial properties, subject to consultant approval. Its white finish works well with many standard interior schemes, while the single-socket format is useful where only one controlled outlet is required.

Installation should be completed by a licensed electrician. The circuit must first be isolated, locked out where required and tested to confirm it is dead. The live, neutral and earth conductors should then be identified, terminated at the correctly marked terminals and tightened to the manufacturer's specified torque. The socket should be secured to a compatible wall box without trapping conductors, after which continuity, polarity, insulation resistance, earth-fault protection and functional operation should be tested.

A compatible single-gang flush or surface mounting box with suitable fixing centres and adequate depth is required. Box depth should allow safe conductor bending and terminal clearance. Cable size, protective device rating, earthing arrangement and RCD or RCBO protection must follow the approved circuit design and applicable UAE electrical regulations. Compatibility should be checked before bulk procurement for a project.

Yes. The protective earth conductor must be connected to the designated earth terminal, and any metal back box should also be correctly bonded where required. Effective earthing is essential for fault protection. The electrician must test earth continuity and confirm that the circuit's protective device will disconnect within the required time under fault conditions.

Its use depends on the installation zone, enclosure protection and local regulations. Because no specific IP rating is provided in the product data, the BL237 should not be assumed to be weatherproof or suitable for direct exposure to water, dust, humidity or outdoor conditions. Wet areas, balconies, gardens and construction sites generally require appropriately rated enclosures, suitable RCD protection and accessories selected for the environmental conditions.

It may be used as a replacement when the wall box, fixing arrangement, wiring condition, circuit rating and applicable standard are compatible. Before replacement, an electrician should inspect the conductors for heat damage, loose terminations, inadequate earth continuity or insufficient box depth. The circuit must be tested after installation rather than treating the work as a simple faceplate change.

Double-pole switching isolates both live and neutral at the socket, offering a clear local means of disconnecting connected equipment. This is beneficial for everyday appliance control and maintenance in homes, offices, shops and hospitality properties. It does not replace circuit isolation, however; electricians must still isolate and verify the supply before carrying out electrical work.

A standard indoor socket should not automatically be used as an exposed temporary site outlet. UAE construction sites can involve dust, moisture, impact and harsh handling, so temporary distribution systems normally require robust industrial accessories, suitable IP ratings, RCD protection and compliance with site safety procedures. The BL237 is better suited to completed indoor fixed installations unless it is housed in a properly designed and approved protective assembly.

Testing should form part of the complete circuit verification process and include protective conductor continuity, insulation resistance, polarity, earth-fault loop or equivalent protective measures, RCD or RCBO operation where fitted, and a functional check of the double-pole switch. Results should be recorded in the project's inspection and testing documentation in accordance with the consultant's requirements and relevant UAE regulations.

Switch off and isolate the circuit before inspection or cleaning. Wipe the faceplate with a soft, dry or slightly damp cloth and avoid solvents, abrasive cleaners and water entering the socket apertures. Replace the accessory if there are signs of cracking, discoloration, overheating, arcing, loose mounting or unreliable switching, and have the connected circuit inspected by a qualified electrician.