ABB Inora 2 Gang 1 Way 10AX Switch Classic Grey BL102-G

Two gang means the switch has two individual rockers for operating two separate circuits. One way means each circuit is controlled from one switch location rather than from multiple locations. The 10AX designation indicates a 10 A switch rating with additional suitability for certain lighting loads that can produce higher switching currents. The connected load must still be checked against ABB's technical data and the lighting manufacturer's requirements.

This ABB Inora switch can be used for indoor lighting control in villas, apartments, offices, shops, hotels and other building fit-outs. Typical applications include controlling two room lights, separate lighting zones, or a main light and another suitable fixed lighting circuit from one wall position. Environmental suitability and the connected load should be confirmed before installation.

Yes. Each rocker is intended to operate a separate one-way circuit, allowing two compatible lights or lighting groups to be switched independently from the same location. The circuits must be correctly wired and remain within the switch rating and the applicable electrical design limits.

It may be used with compatible LED lighting circuits, provided the LED drivers' steady-state current and inrush current are within ABB's specified switching limits. LED drivers can generate a brief, high startup current, so the number and wattage of fittings should not be selected using wattage alone. For larger LED groups, an electrician or electrical engineer should confirm whether a contactor or other control device is required.

Installation should be completed by a qualified electrician. The supply must be isolated, locked out where applicable and proven dead before work begins. The electrician should verify the circuit arrangement, connect the permanent live and the two switched-live conductors to the terminals identified on the product, secure the switch to a compatible concealed or surface box, fit the front assembly correctly and complete continuity, insulation-resistance, polarity and functional testing. Always follow the ABB wiring markings and installation instructions supplied with the product.

Use a wall box, mounting arrangement and associated accessories that match the ABB Inora device dimensions and fixing pattern. The box should provide adequate depth for conductors and safe terminal clearance without crushing or sharply bending the wiring. Because box standards and site conditions vary, contractors should verify compatibility with the approved project accessory schedule and obtain matching ABB components where required.

The ABB Inora BL102-G is relevant to UAE residential and commercial projects requiring a two-gang, one-way lighting control in a neutral classic grey finish. Before specifying it, consultants and contractors should verify its documentation, voltage and frequency suitability, mounting compatibility and project approval requirements against the current rules of the relevant UAE authority, such as DEWA, ADDC, SEWA or the applicable local authority.

Installation should comply with the current UAE electrical regulations, the requirements of the relevant local utility or authority, the project's approved specifications and the manufacturer's instructions. UAE projects commonly reference BS 7671 principles for low-voltage electrical installations, but the authority having jurisdiction and approved project documents take precedence. Product certification and conformity documents should be confirmed when required for consultant or authority approval.

No. A one-way switch is intended to control each connected circuit from one location. Staircases, corridors and rooms requiring control from two positions normally need two-way switching devices and the appropriate interconnecting wiring. Confirm the switching design before ordering accessories for the project.

It should not be assumed suitable for socket outlets, air conditioners, water heaters, pumps or other high-current equipment simply because it carries a 10AX rating. It is primarily specified as a lighting switch. Heavy or inductive equipment should use correctly rated isolators, switches, contactors or control devices selected by an electrical engineer according to the equipment load and UAE installation requirements.

Do not use it in exposed outdoor, damp or wet locations unless the complete installed assembly has a confirmed ingress-protection rating appropriate for that environment. Bathrooms, utility areas, gardens and external walls may require weatherproof accessories, suitable enclosures and installation outside restricted zones. The location should be assessed by a qualified electrician under applicable UAE regulations.

The classic grey finish coordinates well with concrete-effect surfaces, metallic details, neutral paint palettes and contemporary residential or commercial interiors. It can help contractors and designers maintain a consistent accessory schedule across rooms, although the exact colour and matching ABB plates or accessories should be verified before bulk project procurement.

Confirm model number BL102-G, two-gang one-way functionality, 10AX rating, classic grey colour, required quantity, matching mounting boxes and any coordinating plates or accessories. Contractors should also check the approved material submittal, circuit schedules, lighting load and driver inrush data, installation environment, consultant requirements and local authority compliance documentation before placing a project order.

Isolate the electrical supply before inspection or maintenance. Clean the visible surface with a soft, dry or lightly damp cloth and avoid abrasive pads, solvents, strong chemicals or excessive water. If a rocker becomes loose, overheats, crackles, discolours or operates intermittently, stop using the circuit and have the switch and wiring inspected by a qualified electrician.