ABB Inora 2 Gang 1 Way 10AX Switch Royal Gold BL102-PG

“2 gang” means the switch has two independently operated controls. “1 way” means each connected circuit is controlled from one switch location rather than from two locations. “10AX” denotes a switching rating designed to accommodate lighting loads, including the higher inrush currents that can occur with certain fluorescent, LED-driver and inductive lighting equipment. The connected load must remain within the manufacturer's stated electrical rating.

Yes. Each rocker can normally control a separate lighting circuit, such as a ceiling light and wall lights, provided the circuits are correctly designed and wired. It can also be used for two lighting zones in the same room. Both loads must be compatible with the switch rating, and installation should be completed by a qualified electrician.

No. The BL102-PG is a 1 way switch intended to control each circuit from one location. A staircase, long corridor or room requiring control of the same light from two positions generally needs compatible 2 way switches and suitable interconnecting wiring. Confirm the required switching arrangement before ordering.

It is designed for fixed wiring applications and is relevant to typical UAE residential, commercial and hospitality projects when its voltage, load rating, mounting arrangement and certification meet the project specification. UAE low-voltage supplies are commonly 230 V at 50 Hz, but compatibility must be verified against the ABB technical documentation and the requirements of the applicable local authority, such as DEWA, ADDC or the relevant emirate's utility provider.

It can be used to switch compatible LED lighting circuits when the total operating current and driver inrush current are within the manufacturer's limits. LED drivers may draw a brief startup current significantly higher than their normal running current, especially when several fittings are connected together. For large LED circuits, consult the lighting driver data and use a suitably rated contactor or switching device if required.

This model is an on/off wall switch and should not be assumed to function as a dimmer, fan-speed regulator, isolator or socket outlet switch. Motor and fan loads can have different starting-current and isolation requirements. Use a purpose-designed fan controller, dimmer or double-pole isolator where specified by the electrical design.

Before installation, the circuit must be isolated at the distribution board, locked out where applicable and proven dead with an approved tester. The electrician should identify the incoming live conductors and switched-live conductors, connect each gang according to the ABB terminal markings, secure the mechanism in a compatible wall box and fit the faceplate evenly. The circuit should then be tested for continuity, insulation resistance, polarity and correct operation before energisation.

A conventional mechanical 1 way switch normally interrupts the live conductor and may not require a neutral connection at the switch mechanism. However, neutral and protective earth conductors must be managed according to the actual circuit design, terminal instructions and local wiring regulations. Never use the protective earth conductor as a neutral or switched-live conductor.

Use a compatible flush or surface mounting box with adequate depth for the switch mechanism, terminal connections and conductor bend radius. Box dimensions, fixing centres and plate compatibility should be checked before installation, particularly when replacing another brand or accessory range. Suitable insulated conductors, approved connectors, an earth terminal and correctly rated circuit protection may also be required.

The royal gold finish is well suited to premium villas, apartments, hotels, majlis areas, reception spaces and high-end retail interiors. It can coordinate with warm metallic fittings and decorative finishes. The switch is intended for suitable indoor locations; avoid exposure to rain, excessive moisture, construction chemicals, abrasive cleaners and heavy dust unless it is installed within an appropriately rated enclosure.

Installation in bathrooms, wet areas or outdoor locations depends on the required ingress protection rating and the position of the accessory relative to water sources. Do not treat a standard decorative switch as weatherproof. UAE projects should follow the applicable bathroom-zone, outdoor wiring and local authority requirements, using a suitably IP-rated enclosure or accessory where moisture or dust exposure is expected.

Contractors should verify the model number BL102-PG, 2 gang 1 way function, 10AX rating, supply compatibility, connected-load characteristics, back-box dimensions, fixing arrangement, conductor capacity, finish and required quantity. They should also confirm compliance documentation against the project's approved material submittal, consultant specification and relevant UAE authority requirements before procurement.

Keep the switch in its original packaging until the area is dry, clean and ready for second-fix installation. Protect the royal gold surface from paint, plaster, grout, silicone, solvents, cement dust and impact damage. Do not cover an energised switch with combustible protective material, and clean the faceplate only with a soft, lightly damp cloth after isolating the supply.

Installation should be carried out by a qualified electrician familiar with UAE electrical regulations, the project's approved drawings and the requirements of the relevant utility or authority. Correct circuit isolation, conductor identification, termination torque, earthing and post-installation testing are essential for safe and reliable operation.