ABB Inora 2 Gang 2 Way 10AX Switch Classic Grey BL106-G

A 2 gang switch contains two separate switching mechanisms on one faceplate. The 2 way configuration means each circuit can be connected with a second compatible two-way switch so that the same light can be operated from two locations. The 10AX designation indicates a 10 A switch rating designed to accommodate the switching characteristics of lighting loads, including loads that may have higher starting or inrush current than basic resistive loads.

This switch is suitable for indoor lighting control in villas, apartments, offices, hotels, retail units and other commercial or residential buildings. Typical applications include controlling two separate lighting zones from one location, such as ceiling lights and wall lights, or creating two-way control at corridors, staircases, bedrooms and rooms with more than one entrance.

Yes. Each gang can form part of a two-way lighting circuit when connected to another compatible two-way switch using the correct common and traveller conductors. This arrangement is commonly used at opposite ends of staircases and corridors or near two entrances to the same room. Both switch locations must be wired correctly for two-way operation.

A two-way switch can generally be wired for one-way operation by using the common terminal and one appropriate switched terminal for each gang. The unused terminal remains unconnected. Terminal identification and the wiring diagram supplied with the product should always be followed, and installation should be completed by a qualified electrician.

The switch is relevant to UAE residential and commercial projects where its marked electrical rating, mounting arrangement and circuit application match the project specifications. The installer must verify compatibility with the local nominal supply, approved wiring accessories and the requirements of the applicable authority, such as DEWA, ADDC or the relevant emirate-level utility and municipality regulations.

Before installation, isolate and verify the electrical supply as de-energised. Fit a compatible flush or surface mounting box, route the specified conductors and identify the incoming live, switched live and traveller wires. Connect each gang according to the terminal markings and ABB wiring instructions, secure the mechanism without trapping conductors, align the faceplate and restore power only after continuity, insulation and functional testing. Installation should be performed by a licensed or qualified electrician.

Each two-way circuit normally requires a common connection plus two traveller or strapper connections between the paired switches. Because this model has two gangs, separate conductor sets are required for the two controlled circuits. Cable size, conductor identification, earthing provisions and containment must follow the approved electrical design and applicable UAE wiring regulations. The product terminal markings should take precedence over generic diagrams.

It may be used to switch compatible LED lighting circuits provided the total connected load and driver inrush current remain within the switch manufacturer's rating. LED drivers can create a brief high starting current even when their normal wattage is low, so the electrician or project engineer should check the number and specifications of the connected drivers rather than relying only on total lamp wattage.

The BL106-G is primarily intended as a lighting control switch. It should not be assumed suitable for socket outlets, water heaters, air-conditioning equipment, pumps or other heavy or motor-driven loads. Such circuits may require a higher-rated double-pole switch, isolator, contactor or dedicated control device selected according to the equipment load, starting current and approved electrical design.

Use in bathrooms, wet rooms, balconies or exposed outdoor locations depends on the required ingress protection rating and installation zone. The available product data does not specify an IP rating for the BL106-G, so it should not be treated as weatherproof or splashproof unless confirmed by ABB documentation. For damp or outdoor areas, select a suitably IP-rated accessory and follow local bathroom-zone and outdoor electrical requirements.

Contractors should verify the model number BL106-G, 2 gang and 2 way configuration, 10AX rating, classic grey finish, mounting-box compatibility, terminal arrangement and required quantity. They should also review the approved material submittal, electrical load schedule, consultant specifications and local authority requirements to ensure consistency across the project.

Routine maintenance is limited to keeping the faceplate clean and checking for loose operation, overheating, discoloration, arcing sounds or intermittent switching. Clean only with a soft, dry or slightly damp cloth and avoid solvents or abrasive chemicals. If any fault is observed, isolate the circuit and have a qualified electrician inspect the wiring, terminals and connected load.

The ABB Inora BL106-G combines two independent two-way lighting controls in one wall accessory, helping reduce wall-plate space while supporting practical multi-location switching. Its classic grey appearance suits modern villas, offices, hospitality spaces and commercial fit-outs where coordinated electrical accessories and a neutral contemporary finish are required.