ABB Inora 2 Gang 2 Way 10AX Switch Starry Black BL106-885

“2 gang” means the switch has two independently operated rockers for two separate circuits. “2 way” means each circuit can be wired with another compatible two-way switch so that the same light can be operated from two locations. “10AX” is a switching rating intended for lighting circuits and accounts for the demanding switching characteristics of certain inductive or fluorescent loads. Connected loads must still be checked against ABB technical data and project requirements.

This switch is suitable for residential villas, apartments, offices, hotels, retail units and other UAE building interiors. Typical uses include controlling two room lighting circuits, separate groups of downlights, or indoor and balcony lighting from one position. Two-way switching is especially useful in corridors, staircases, bedrooms and rooms with more than one entrance.

Yes. Each gang is designed as a two-way switch and may form part of a separate two-way lighting circuit when connected to another compatible two-way switch. It can also generally be used for conventional one-way switching by using the appropriate common and switched terminals. Wiring must follow the terminal markings and ABB installation instructions.

It can be used with many LED lighting circuits, provided the total load and the LED driver’s inrush current are compatible with the switch rating. LED drivers can produce a brief starting current significantly higher than their normal operating current, so wattage alone should not be used to determine compatibility. For large groups of LED fittings, consult the driver manufacturer and ABB technical data or use a suitably rated contactor or control device.

Installation should be completed by a qualified electrician. The circuit must be isolated, locked off where applicable and verified dead before work begins. Conductors should be identified and connected to the marked common and two-way terminals for each gang, with no exposed copper outside the terminals. The mechanism should then be secured level in a compatible wall box, the faceplate fitted and the circuit tested for correct operation, polarity and electrical safety.

Use a flush or surface wall box that is compatible with the ABB Inora switch dimensions, fixing centres and terminal depth. The product’s two-gang appearance does not automatically indicate that every generic two-gang back box will fit. Before installation, verify the ABB dimensional drawing and ensure the box has enough depth for the switch mechanism, conductors and safe cable bending, particularly where two-way wiring adds extra conductors.

Yes. The Starry Black finish is well suited to contemporary villas, apartments, offices, hospitality spaces and retail interiors. It can complement dark joinery, black accessories, stone finishes and modern decorative themes. For a coordinated installation, use matching ABB Inora accessories from the same colour and design range wherever available.

It should only be installed where the product’s confirmed environmental and ingress-protection ratings meet the location requirements. As no outdoor or weatherproof rating is stated in the supplied product information, it should be treated as an indoor accessory for suitable dry locations unless ABB documentation confirms otherwise. Bathrooms, wash areas, balconies and external locations may require designated zones, suitable IP-rated enclosures and additional protection.

The switch is relevant to UAE residential, commercial and fit-out projects requiring a branded 2 gang 2 way 10AX lighting switch with a dark decorative finish. Product selection and installation must comply with the approved project specification, applicable UAE electrical regulations and the requirements of the relevant local authority, such as DEWA or the authority serving the project location. Consultant approval and required conformity documentation should be confirmed before bulk procurement.

The electrician should verify terminal tightness, conductor identification, polarity, protective-conductor continuity where applicable, insulation resistance and correct two-way operation from every control point. The circuit protective device and connected lighting load should also be checked for suitability. Testing and documentation should follow the project’s inspection and testing procedure and applicable UAE authority requirements.

This product is primarily intended as a lighting switch and should not be assumed suitable for socket outlets, water heaters, air conditioners, pumps, large fans or other heavy loads. Equipment with high running or starting current may require a dedicated isolator, double-pole switch, contactor or controller with the correct rating. Always check the equipment load type and ABB technical specifications before connection.

Contractors should verify the model number BL106-885, Starry Black finish, 2 gang 2 way configuration, 10AX rating, matching Inora accessories, back-box compatibility and project-approved material schedule. They should also confirm the required quantities, sample approval, wiring arrangement, installation depth and any authority or consultant documentation needed for the UAE project.

Isolate the electrical supply if inspection or deeper cleaning is required. Wipe the faceplate gently with a soft, dry or lightly damp cloth and avoid abrasive pads, solvents, bleach and strong chemical cleaners that may damage the finish. If a rocker becomes loose, discoloured, unusually warm or intermittent, stop using the circuit and have the switch inspected by a qualified electrician.