ABB Inora 2 Gang 2 Way 20AX Switch Royal Gold BL115-PG

The term 2 gang means that the plate contains two separate switch controls for operating two circuits. The term 2 way means that each circuit can be switched from either of two locations when connected to another compatible two-way switch. This arrangement is commonly used for staircases, corridors, bedrooms, villas and rooms with more than one entrance.

The 20AX marking indicates the switch's rated switching capacity, including suitability for loads that can produce higher inrush currents, such as certain lighting circuits. Actual circuit loading must remain within the manufacturer's rating and the approved electrical design. An electrician should also confirm compatibility with LED drivers, fluorescent ballasts, contactors and other connected equipment before installation.

It may be used to switch compatible LED lighting circuits, subject to the total load, driver inrush current and ABB's product requirements. LED drivers can draw a brief startup current significantly higher than their normal operating current, so suitability should not be assessed from wattage alone. For large LED circuits, the electrical designer may specify a suitably rated contactor or relay.

The ABB Inora royal gold switch is suited to indoor applications in UAE villas, apartments, hotels, offices, reception areas and premium retail interiors. Its two-gang layout is useful where two lighting zones must be controlled from a single point, while its two-way function is relevant to corridors, staircases and rooms with multiple access points. The finish can coordinate with warm metallic hardware and luxury interior schemes.

Installation should be completed by a qualified electrician. The circuit must first be isolated, locked out where required and tested to confirm it is de-energised. The electrician should identify the common and traveller terminals from the markings or ABB instructions, connect the conductors according to the approved wiring diagram, verify the earth continuity and terminal tightness, mount the mechanism without trapping wires, and then test both gangs from every control location. Do not rely on wire colour alone when identifying conductors.

The switch should be fitted to a compatible flush or surface mounting box that matches the product's fixing arrangement and provides adequate space for conductors and terminals. Required box depth can vary with cable size, conduit entries, wiring configuration and the number of conductors used for two-way switching. Confirm the ABB dimensional data and coordinate the box type and depth before blockwork, drywall closure or final electrical fixing.

A two-way switch can generally be wired for one-way control by using the common terminal and one appropriate switched terminal for each gang. However, the work must follow the terminal markings and ABB installation instructions. A qualified electrician should verify the wiring arrangement, conductor identification and circuit protection before energising the installation.

The 20AX designation does not automatically make the switch suitable as an isolator for water heaters, air conditioners, motors or other heavy appliances. Such loads may require a double-pole switch, fused connection unit, local isolator, contactor or another purpose-designed control device. Selection must be based on the load type, starting current, pole arrangement and applicable UAE electrical requirements.

Use in bathrooms, wet areas, kitchens or outdoors depends on the required ingress protection, installation zone and local regulations. Unless the documented product rating confirms suitability for the location, it should be treated as an indoor switch for dry areas. Locations exposed to water, condensation, dust or UAE outdoor conditions should use an appropriately IP-rated accessory or weatherproof enclosure.

Installation should comply with the applicable regulations of the relevant UAE authority, project specifications and recognised wiring practices, which may include BS 7671 where adopted. Requirements can differ between jurisdictions and developments, including DEWA, TAQA Distribution and other local authorities. Circuit protection, conductor sizing, earthing, mounting location, testing and certification should be handled by an authorised electrical contractor.

Contractors should confirm the model number BL115-PG, royal gold finish, 2 gang 2 way configuration, 20AX rating, required quantity and compatibility with the selected wall boxes and other ABB Inora accessories. They should also verify the lighting load type, two-way wiring locations, approved material schedule and finish sample. Early coordination helps avoid mismatched plates, insufficient back-box depth and incorrect first-fix cabling.

Keep the switch covered during painting, plastering, sanding and other dusty works, and install decorative components as late as practical in the finishing programme. Clean the surface with a soft, dry or slightly damp cloth. Do not use abrasive pads, solvents, acidic cleaners or strong chemicals, as these may damage or discolour the royal gold finish. The circuit should be isolated before cleaning around the switch.