ABB Inora 2 Gang RJ45 Cat 5e Data Outlet Classic Grey BL332-G

When correctly terminated as part of a compliant Category 5e channel, the socket can support Ethernet applications up to 1 Gigabit per second, including 10BASE-T, 100BASE-TX and 1000BASE-T. Actual performance depends on cable quality, total channel length, termination workmanship, patch cords and connected network devices.

A CAT.6 cable may be physically connected if the conductor size and termination format are compatible, but the completed link will generally be limited by the lowest-category component, which is CAT.5e in this case. For a certified CAT.6 installation, use CAT.6-rated sockets, cable, patch panels and patch cords throughout the channel.

The socket should be mounted in a compatible wall box or containment system and terminated using the wiring guide marked on the data module. Route the network cables into the box without sharp bends, maintain the pair twists as close as possible to the termination points, secure the conductors with the appropriate IDC termination tool where required, and fit the socket plate squarely to the wall. Installation and testing should be performed by a qualified ELV or structured-cabling technician.

Either T568A or T568B may be used if supported by the terminal colour code, but the same wiring scheme must be maintained at both ends of each permanent link. T568B is common in many commercial installations, while project specifications may require a particular scheme. Mixing T568A and T568B unintentionally can create a crossover connection and cause testing or network issues.

For standards-based Ethernet cabling, the permanent link is normally limited to 90 metres, with the complete channel limited to 100 metres including patch cords. Cable routing, bend radius, termination quality and separation from electrical services must also meet the project specification and applicable structured-cabling standards.

Yes, it is suitable for indoor structured-cabling applications commonly required in UAE villas, apartments, offices, retail spaces, schools and hospitality projects. Its two data outlets help serve locations that require multiple wired connections, such as workstations, television areas, reception desks and meeting rooms. Compatibility with the specified back box, faceplate system and project-approved materials should be confirmed before installation.

It may be positioned in the same user area as power outlets, but data cabling should be segregated from mains wiring in accordance with the project design, local authority requirements and relevant electrical and structured-cabling practices. Use suitable compartmented trunking or separate conduits where required, avoid long parallel runs beside power cables, and cross power cables at approximately 90 degrees when unavoidable.

A properly installed CAT.5e link can carry Power over Ethernet for compatible devices such as IP phones, wireless access points and some CCTV cameras. PoE performance depends on the complete cabling channel, conductor quality, termination integrity, cable bundle size and the power level required by the device. The installer should confirm that all components meet the applicable PoE and project requirements.

Yes, it can form part of a CAT.5e network connection for IP CCTV cameras, network video equipment and monitoring workstations. For camera locations, ensure that the cable distance is within Ethernet limits and that any PoE requirements are supported by the complete link. This indoor wall socket should not be placed in exposed outdoor or wet locations unless protected by a suitable weather-resistant enclosure.

Each outlet should be checked for correct wire map, continuity, pair sequence, shorts, opens, split pairs and link length. On professional construction projects, a calibrated cable certifier should be used to verify CAT.5e performance parameters and produce test reports for handover. Both ports should also be clearly labelled to match the corresponding patch-panel positions.

Use genuine solid-conductor CAT.5e installation cable from a suitable source, avoid excessive pulling tension, do not crush the cable with ties or clips, maintain the manufacturer's minimum bend radius, and keep pair untwisting at the termination to a minimum. Data cables should also be kept away from high-current circuits, motors, transformers and other sources of electromagnetic interference.

No. The socket is a passive structured-cabling component and does not require a separate electrical supply. It provides the physical termination between fixed network cabling and Ethernet patch cords. Network connectivity is supplied by connected equipment such as a router, switch or patch panel, while PoE power, if used, is delivered through compatible network equipment.

The classic grey finish is well suited to contemporary offices, commercial spaces, utility rooms and modern residential interiors where a neutral electrical-accessory colour is preferred. For a coordinated appearance, confirm that adjacent ABB Inora switches, sockets, frames and accessories use the same finish and compatible product range.

Contractors should verify the model number BL332-G, required outlet quantity, CAT.5e project specification, wall-box and mounting compatibility, available installation depth, cable termination method, colour schedule and indoor environmental conditions. They should also confirm whether the project requires unshielded or shielded cabling, because every component in the channel must match the specified system.