ABB Inora 2 Gang RJ45 Cat 5e Data Outlet Royal Gold BL332-PG

CAT.5e structured cabling is specified for frequencies up to 100 MHz and can support Ethernet speeds up to 1 Gigabit per second when the complete channel is correctly designed, terminated and tested. Actual performance depends on the cable, patch panels, patch cords, installation quality, network equipment and total channel length.

Yes. Each data port should be connected to its own CAT.5e cable run and its own network switch or patch-panel port. The socket does not split one Ethernet cable into two active connections, and it does not operate as a network switch.

Installation should be completed by a qualified ELV or structured-cabling technician. Isolate the work area, confirm the compatible wall box and mounting arrangement, route one CAT.5e cable to each port, terminate all four twisted pairs using the selected T568A or T568B scheme, maintain the cable twists close to the terminals, secure the outlet without crushing the cables, and test both links before handover. Follow ABB instructions and the approved project drawings.

Either T568A or T568B may be used if supported by the socket termination markings and project specification. The same wiring scheme must be applied at both ends of each cable run. T568B is common in many commercial installations, but contractors should follow the consultant-approved structured-cabling standard for the UAE project.

Avoid excessive pulling tension, sharp bends, crushed cables and unnecessary untwisting of conductor pairs. Keep data cabling separated from power cables and sources of electromagnetic interference in accordance with the project specification and applicable regulations. Use suitable containment, label both ends, protect cables from dust and moisture during construction, and certify every completed link with a calibrated cable tester.

A standards-based Ethernet channel is generally limited to 100 metres, commonly comprising up to 90 metres of permanent horizontal cable plus patch cords with a combined allowance of up to 10 metres. Designers should also consider routing, patching and manufacturer requirements rather than measuring only the distance from the outlet to the switch.

Yes, it is suitable for indoor structured-cabling applications in UAE villas, apartments, offices, hotels, shops and other commercial developments where two wired data points and a decorative Royal Gold finish are required. Compatibility with the selected Inora accessories, wall box, project finish schedule and approved material submittal should be confirmed before procurement.

It should be treated as an indoor data outlet unless ABB documentation confirms a specific ingress-protection rating. For balconies, gardens, plant rooms, wash areas or other dusty and humid UAE environments, use a suitably rated weatherproof enclosure and components selected for the environmental conditions.

CAT.5e cabling can be used for many Power over Ethernet applications, including IP phones, cameras and wireless access points. However, the complete link—including the socket, cable, patch panel, connectors and switch—must be suitable for the required IEEE PoE type and power level. Confirm the product's applicable ratings and the project specification before using it for higher-power PoE loads.

Test each port independently for wire map, continuity, pair configuration, length and relevant CAT.5e transmission parameters. On projects requiring certification, use a calibrated field tester configured to the specified permanent-link or channel standard, then identify each outlet and include the test reports in the ELV handover documents.

The installation should follow the approved UAE project specification, local authority requirements and recognised structured-cabling practices such as ISO/IEC 11801 and ANSI/TIA-568 series requirements where specified. Contractors should also comply with consultant drawings, separation requirements, fire-stopping rules and any applicable UAE fire and life-safety provisions for cable routes and penetrations.

It may be used for compatible structured voice applications when correctly patched and wired, but it must not be connected directly to unsuitable electrical or analogue services. The outlet should be clearly labelled to prevent confusion between LAN, IP telephony and other ELV systems.

Confirm the model number BL332-PG, Royal Gold finish, required number of data ports, CAT.5e project requirement, compatible ABB Inora plate or mounting accessories, wall-box arrangement and termination method. Also check whether the project bill of quantities requires matching patch panels, CAT.5e cable, patch cords, labels and test certification.

Disconnect connected equipment where necessary and wipe the visible surface with a soft, dry or lightly damp cloth. Do not use abrasive pads, solvents, acidic cleaners or strong construction chemicals, as these may damage the decorative finish. Prevent paint, gypsum dust and sealants from entering the data ports during fit-out work, and use suitable port covers until final handover.