ABB Inora 2 Gang Data Outlet Housing Classic Grey BL332-H-G

This face plate is suitable for indoor data outlet locations such as offices, meeting rooms, apartments, villas, hotels, retail premises, schools, control rooms and other structured cabling installations. It can be used where network or communication points must be presented with a clean, professional wall finish.

A 2-gang face plate provides a wider mounting format than a standard single-gang plate, allowing compatible data modules to be arranged within the designated outlet area. The exact number and type of RJ45, telephone or multimedia modules that can be fitted depend on the ABB Inora module system and mounting accessories selected. Check module dimensions and system compatibility before installation.

The product is described as a data face plate, so RJ45 keystone jacks, data modules, cables and termination hardware should not be assumed to be included unless specifically stated in the order specification. Select compatible Cat6, Cat6A or other required modules according to the project network design and confirm compatibility with the ABB Inora range.

Install a compatible 2-gang back box at the specified finished-wall position, route the structured cabling with adequate service length and terminate each cable on the approved data module using the module manufacturer's wiring method. Fit the modules into the compatible support or mounting frame, align the face plate and secure it without overtightening. Label the ports and test every completed link before handover. Installation should be performed by a qualified ELV or structured cabling technician.

Use a 2-gang back box and mounting arrangement that are dimensionally compatible with the ABB Inora BL332-H-G system. Back-box depth must also accommodate the selected data modules, cable bend radius and termination space without compressing the cable. Because back-box standards and module formats can differ, verify the ABB product documentation, project drawings and actual site accessories before installation.

The face plate may be used as part of a Cat6 or Cat6A outlet when fitted with compatible modules of the required category. The face plate itself does not determine network performance; channel performance depends on the jack, cable, patch panel, patch cords, termination quality and compliance of the complete permanent link. Cat6A installations may require deeper boxes and additional space for the larger cable diameter and bend radius.

The completed data outlet should follow the project specification and recognised structured cabling practices such as ISO/IEC 11801 or ANSI/TIA-568 where applicable. Maintain the cable manufacturer's minimum bend radius, avoid excessive pulling tension, preserve pair twists close to the termination and keep data cabling separated from power circuits in accordance with local electrical requirements. Test and document each link using equipment appropriate to the specified cable category.

Yes, it is suitable for indoor UAE residential and commercial projects when the complete installation meets the consultant's specifications, relevant authority requirements and approved material schedule. Its classic grey finish can complement contemporary interiors and service areas. For projects in Dubai, Abu Dhabi or other emirates, installers should also follow the applicable local electrical, ELV and telecom infrastructure requirements.

It may be positioned near electrical accessories when permitted by the approved layout, but power and data services should use the required segregation, partitions, conduits and back boxes. Avoid routing network cables alongside mains wiring for unnecessary distances because electromagnetic interference can affect performance. Follow UAE authority rules, project specifications and the cable manufacturer's separation recommendations.

This type of decorative data face plate is generally intended for dry indoor locations. It should not be used in exposed outdoor, wash-down, dusty or high-humidity areas unless the completed enclosure has a verified ingress-protection rating suitable for that environment. For UAE outdoor sites, plant rooms or semi-exposed locations, use a purpose-designed weatherproof data enclosure.

For blockwork, install and level the concealed back box before plastering, allowing for the final plaster or tile thickness. For drywall, use an approved hollow-wall box or bracket secured to the framing system. For joinery or raised-floor service outlets, confirm cut-out dimensions, fixing support and cable access before fabrication. The finished box should sit square and at the correct depth so the plate fits flush without gaps.

Switch off or isolate nearby electrical services where necessary, then wipe the plate with a soft, dry or slightly damp cloth. Do not use abrasive pads, solvents or aggressive chemical cleaners that may damage the classic grey finish. Periodically check that the plate remains secure, port labels are readable and data modules have not become loose.

Confirm the model number BL332-H-G, classic grey colour, 2-gang box format, compatible ABB Inora mounting frame and required data modules. Also verify the cable category, number of ports, back-box depth, wall construction, outlet schedule and consultant-approved finish. This coordination helps prevent mismatched modules or insufficient termination space on site.

After termination, visually inspect the face plate, labels, module seating and cable management. Test each network link for wire map, continuity, length and the performance parameters required by the specified category. Record the outlet identification and test result in the project documentation; certification testing should be carried out with a calibrated field tester when required by the consultant or client.