ABB Inora 2 Gang Data Outlet Housing Royal Gold BL332-H-PG

Two gang indicates that the face plate is configured to accommodate two compatible data outlet positions or modules. Depending on the selected ABB Inora mechanisms, these positions may be used for network, telephone or other extra-low-voltage communication connections. The module type and mounting arrangement must be verified before installation.

The BL332-H-PG should be used with data modules and mounting components designed for the relevant ABB Inora range. Do not assume that third-party RJ45, telephone or multimedia modules will fit solely because their openings appear similar. Confirm the module dimensions, mounting method, category rating and ABB product compatibility before ordering.

It may form part of a Cat6 or Cat6A outlet installation when fitted with compatible data modules of the required category. The face plate itself does not determine network performance. Cable category, connector rating, termination quality, bend radius, shielding, patch panels and testing all affect the final channel performance.

It is suitable for indoor data outlet points in villas, apartments, hotel rooms, reception areas, executive offices, meeting rooms, retail units and other finished interiors. The Royal Gold surface is particularly relevant to UAE projects using decorative metallic accessories. Suitability for exposed outdoor, wet, dusty or industrial locations should not be assumed unless the complete assembly has the required environmental and IP rating.

First isolate nearby electrical circuits and confirm that the wall box, mounting frame and data modules are compatible. Route and terminate the communication cables according to the module manufacturer's instructions, maintain the specified bend radius, secure the modules in the support frame and align the face plate before fixing it evenly. Installation should be completed by a qualified ELV or structured-cabling technician to avoid damaged clips, pinched cables or poor data performance.

The concealed or surface back box must match the ABB Inora mounting arrangement and provide sufficient depth for the selected connectors and cable bend radius. During blockwork, drywall or joinery preparation, coordinate the box position, opening size, finished wall thickness and cable entry points. Always verify dimensions from current ABB technical documentation or the approved project submittal before cutting or casting openings.

Contractors should coordinate data outlet locations with electrical drawings, furniture layouts, television points, workstations and Wi-Fi or telecom requirements. Install suitable conduits and back boxes at the correct level, keep data routes separated from power circuits as required by the project specification, protect cable ends from plaster and debris, and leave enough cable for proper termination. Final face plates should normally be fitted after painting and major finishing work.

Yes, it is relevant to UAE residential, hospitality and commercial projects that specify ABB accessories and decorative Royal Gold finishes. The complete data installation should comply with the approved project specification, applicable UAE authority requirements, local telecom or structured-cabling guidelines and the manufacturer's instructions. Consultants and contractors should obtain approval for the full outlet assembly rather than assessing the decorative face plate alone.

Power and data services should generally be separated to reduce electrical interference and maintain safety. Where both services are positioned together, use an approved segregated system, compatible partitions and the clearances required by local regulations, project specifications and manufacturer guidance. A data face plate should not be treated as a substitute for electrical segregation.

Use cable and modules of matching category, follow the specified wiring scheme consistently, keep untwisted conductor lengths to a minimum and avoid tight bends, crushing or excessive pulling force. Shielded systems must have the correct compatible components and earthing arrangement. After installation, test and label every data link using suitable certification equipment where required by the project.

Disconnect or protect nearby services before cleaning, then wipe the surface gently with a soft, dry or slightly damp cloth. Avoid abrasive pads, metal polish, solvents, acidic cleaners and harsh chemicals because they may damage the decorative finish. During construction, protect the plate from paint, gypsum, cement dust, sealants and impact damage.

Confirm the model number BL332-H-PG, Royal Gold finish, required two-gang configuration, compatible ABB Inora modules, mounting frame and back box. Also check the number and type of data ports required, such as RJ45 network or telephone connections. Reviewing the consultant-approved accessory schedule helps prevent mismatched finishes or incompatible components.

The product name identifies a data face plate and does not confirm that RJ45 connectors, data modules, mounting frames, back boxes, cables or patching accessories are included. These components are commonly selected separately according to the network category and project design. Check the supplied item details and approved ABB component list before installation.