ABB Inora 2 Gang Data Outlet Housing White BL332-H

A 2 gang face plate is intended to accommodate two compatible outlet positions or data modules, subject to the ABB Inora module configuration being used. This allows installers to terminate two services at one wall point, such as two Ethernet connections or a combination of data and telephone outlets. Confirm the module type and mounting arrangement before ordering.

The BL332-H should be paired with data modules and mounting accessories compatible with the ABB Inora range and its specified aperture or support system. Do not assume that every RJ45 keystone, telephone module, or third-party insert will fit. Check the module dimensions, fixing method, back-box depth, and ABB compatibility information before installation.

The face plate can form part of a Cat6 or Cat6A structured cabling outlet when fitted with compatible modules rated for the required category. Network performance is determined by the complete channel, including the cable, RJ45 module, patch panel, patch cords, termination quality, and test results. The face plate alone does not establish a Cat6 or Cat6A rating.

It is suitable for indoor low-voltage communication points in villas, apartments, offices, retail units, schools, hotels, and commercial or mixed-use developments. Typical applications include workstation data outlets, Wi-Fi access-point connections, IP telephone points, smart-home networks, and other ELV systems where compatible modules are specified.

First isolate and identify nearby electrical and ELV services, then install a compatible wall or back box at the specified level. Route the data cables without excessive pulling, crushing, or tight bends; terminate each cable onto the correct compatible module according to its wiring scheme; secure the modules in the mounting support; and fix the face plate evenly. Label and test every completed outlet before handover. Installation should follow the project drawings, manufacturer instructions, and approved UAE site practices.

Use a back box and mounting support that match the ABB Inora system, the two-gang arrangement, and the selected data modules. Adequate box depth is important because data modules and cable bend radii need more working space than a decorative plate alone. Verify the box dimensions, screw centres, wall type, module depth, and conduit entry before construction or fit-out work begins.

Yes, it may be used on drywall or masonry installations when an appropriate compatible back box and fixing system are selected. Drywall applications normally require a suitable hollow-wall box, while blockwork or concrete installations typically use a concealed box coordinated before plastering. The finished box should be level, flush, and free from plaster or debris so the plate sits correctly.

Yes, it is well suited to indoor residential and commercial fit-outs in the UAE, particularly where a clean white finish and organised structured cabling outlets are required. Product selection and installation should comply with the project specification, relevant UAE authority requirements, approved ELV drawings, and applicable cabling standards. For regulated or authority-inspected projects, consultant approval should be confirmed before procurement.

Yes. ELV and data cables should be routed with the separation, containment, and crossing arrangements required by the project specification and applicable UAE electrical and telecommunications practices. Avoid sharing unsuitable conduits or boxes with mains wiring, and cross power cables at approximately 90 degrees where crossing cannot be avoided. Correct segregation helps improve safety and reduce electromagnetic interference.

Maintain the specified cable bend radius, preserve pair twists close to the termination, use the module manufacturer's wiring pattern consistently, and avoid excessive untwisting or jacket removal. After installation, test each permanent link with a suitable calibrated cable tester for continuity, wire map, length, and the specified performance category. Label both outlet and patch-panel ends to match the approved network schedule.

This face plate is generally intended for protected indoor locations and should not be treated as weatherproof unless the complete installed enclosure has a specifically declared IP rating. For outdoor, wash-down, humid, or exposed locations in the UAE, use a suitably rated weather-resistant enclosure and compatible accessories selected for the environmental conditions.

Switch off or isolate nearby services where necessary, then wipe the surface with a soft, slightly damp cloth. Do not use abrasive pads, strong solvents, or excessive water, as these may affect the finish or enter the data modules. Periodically inspect the plate for loose fixings, cracks, damaged ports, or missing labels, especially in high-traffic commercial areas.

Confirm the model number BL332-H, required quantity, colour, compatible data modules, mounting support, back-box type and depth, wall construction, and outlet schedule. Also verify whether the project requires RJ45, telephone, fibre, or other ELV inserts, because these components may not be included with the face plate. Coordination before ordering helps prevent compatibility and installation issues.