ABB Inora 2 Gang TV and RJ45 Cat 5e Data Outlet Royal Gold BL325-PG

Switch off or isolate nearby circuits where necessary, then wipe the faceplate with a soft, dry or lightly damp cloth. Do not use abrasive pads, strong solvents or excessive water, as these may damage the Royal Gold finish or enter the connectors. Periodically inspect for loose fittings, damaged ports or unreliable connections and have faults checked by a qualified technician.

Store and install the outlet in a clean, dry environment within the manufacturer's permitted temperature range. Protect it from construction dust, paint, moisture and direct solar heat, particularly before air-conditioning is operational. Avoid crushing or tightly bending data and coaxial cables, label each circuit clearly and complete final testing after all terminations and faceplates are fitted.

Check the compatible mounting box, wall depth, plate and frame arrangement, cable entry space, TV connector requirements, Cat.5e cabling specification and final Royal Gold finish schedule. Contractors should also coordinate outlet positions with joinery, television brackets, furniture, blockwork openings, gypsum partitions and ELV shop drawings to prevent clashes or inaccessible connection points.

It should generally be treated as an indoor wiring accessory unless ABB documentation and the complete enclosure confirm an appropriate ingress-protection rating for the intended location. Do not install it where it may be exposed to rain, washdown, condensation, excessive dust or direct sunlight without a correctly rated protective enclosure and project approval.

The RJ45 port may be used for compatible structured cabling applications when permitted by the system design. Power over Ethernet capability depends on the complete cabling channel, conductor specification, terminations, cable bundling, ambient temperature and connected PoE equipment. Confirm PoE requirements with the network designer and ensure that all components are appropriately specified before use.

Inspect the coaxial termination for secure conductor contact, correct shielding and the absence of shorts between the centre conductor and screen. Measure the signal level and quality at the outlet using suitable TV test equipment, then verify reception across the required services. Poor results may be caused by damaged cable, excessive splitter loss, unsuitable connectors, weak input signal or incorrect amplifier settings.

At minimum, use a network cable tester to check wire map, continuity, open circuits, short circuits, reversed pairs and split pairs. For commercial or consultant-specified projects, certify the permanent link or channel with a calibrated Cat.5e field tester and retain the test reports for inspection, handover and as-built documentation.

Use a project-approved Category 5e twisted-pair cable for the RJ45 data port and a suitable impedance-matched coaxial cable for the TV system, commonly 75-ohm cable where required by the distribution design. Cable fire performance, shielding, conductor construction and jacket classification should match the UAE project specification, building type and authority requirements.

The ABB Inora BL325-PG is a combined wall outlet designed to provide television and wired network connections at one location. It incorporates a TV outlet rated for a 5-1000 MHz frequency range and an RJ45 Category 5e data outlet in a Royal Gold finish. This arrangement is suitable for residential, hospitality, office and mixed-use construction projects where a neat, coordinated TV and Ethernet termination point is required.

Use one consistent termination scheme throughout the structured cabling system, normally T568A or T568B as specified by the consultant or project standard. Do not mix schemes at opposite ends unless a crossover connection is intentionally required. Maintain the cable-pair twists as close as practical to the termination and test the completed link in accordance with the project's selected standard, such as ANSI/TIA-568 or ISO/IEC 11801.

Installation should be completed by a qualified ELV or electrical technician. Isolate nearby electrical circuits, verify the mounting box and accessory compatibility, route the coaxial and Cat.5e cables without sharp bends, terminate each cable using the correct tools and pinout, secure the mechanism without overtightening, fit the Royal Gold front plate and test both services. Follow ABB instructions, approved project drawings and applicable UAE site requirements.

Typical locations include living rooms, bedrooms, hotel guest rooms, meeting rooms, executive offices, reception areas and media walls. It is especially useful behind televisions, entertainment units and workstations where both a coaxial TV feed and a reliable wired Ethernet connection are required.

Yes, it is relevant to UAE villas, apartments, hotels, offices and commercial fit-outs that require integrated TV and wired data points. Its Royal Gold finish can complement premium interior schemes. The consultant, contractor or installer should still verify approval against the project specification, local authority requirements, telecom provider requirements and the selected structured cabling and TV distribution systems.

When installed as part of a standards-compliant Category 5e channel using compatible cable, patch panels, plugs and patch cords, the RJ45 outlet can support common Ethernet applications, including Gigabit Ethernet over channel lengths permitted by the applicable cabling standard. Actual speed depends on the complete network channel, termination quality, cable length, active equipment and site conditions rather than the outlet alone.